Haier UVH13013MTS Use and Care Manual - Page 19

INSTALLATION INSTRUCTIONS, Installation Instructions, A. OUTSIDE TOP EXHAUST

Get Haier UVH13013MTS PDF manuals and user guides View all Haier UVH13013MTS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

INSTALLATION INSTRUCTIONS Installation Instructions A. OUTSIDE TOP EXHAUST (Vertical Duct) (Cont.) A3 ADJUST BLOWER EXHAUST The unit is shipped in the top exhaust configuration. If configuration is not in the top exhaust direction, follow the steps below. CAUTION Wear gloves to protect against sharp edges. 1. Remove damper mounting plate and diverter. 2. Remove diverter from angled position and reinsert vertically as shown. 3. Reattach the damper mounting plate with opening on top of unit as shown. A4 ASSEMBLE AND INSTALL ADAPTOR Screws Damper 1. Remove 3 screws shown above. Position the damper on top of the damper mounting plate and secure with removed screws. 2. Remove the tape from the damper. Make sure that the damper pivots easily before mounting the unit. You will need to make adjustments to assure proper alignment with your house exhaust duct after the unit is installed. 49-2000492 Rev. 2 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
49-2000492
Rev. 2
19
INSTALLATION INSTRUCTIONS
Installation Instructions
A. OUTSIDE TOP EXHAUST
(Vertical Duct) (Cont.)
A3
ADJUST BLOWER EXHAUST
The unit is shipped in the top exhaust configuration.
If configuration is not in the top exhaust direction,
follow the steps below.
CAUTION
Wear gloves to protect against
sharp edges.
1.
Remove damper mounting plate and diverter.
2.
Remove diverter from angled position and reinsert
vertically as shown.
3.
Reattach the damper mounting plate with opening
on top of unit as shown.
A4
ASSEMBLE AND INSTALL
ADAPTOR
1.
Remove 3 screws shown above. Position the
damper on top of the damper mounting plate and
secure with removed screws.
2.
Remove the tape from the damper.
Make sure
that the damper pivots easily before mounting
the unit
.
You will need to make adjustments to assure
proper alignment with your house exhaust duct
after the unit is installed.
Damper
Screws