Hayward Pro Logic® Models: PL-PS-4 PL-PS-8 PL-PS-16 PL-PS-16V Installatio - Page 43

Maintenance Menu

Get Hayward Pro Logic® PDF manuals and user guides View all Hayward Pro Logic® manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

if any output is configured as a variable speed pump VSP Speed % Toggle between % and RPM Move to previous/next configuration menu This is the unit of measure for displaying the speed of the variable speed pump. Select % of maximum speed (3450 RPM) or revolutions per minute (RPM). if ColorLogic Network Module is detected Reset ColorLogic to Initiate reset of ColorLogic configuration parameters Default Press + Move to previous/next configuration menu (config. not reset) Are you sure? + to proceed Reset all configuration parameters Move to previous/next menu (config. not reset) ColorLogic. reset Confirmed Move to previous/next configuration menu Use this function to erase all ColorLogic configuration settings and reset back to the factory default values. This function is NOT reversible--be careful. Reset Config. to Default Press + Initiate reset of all configuration parameters Move to previous/next configuration menu (config. not reset) Are you sure? + to proceed Reset all configuration parameters Move to previous/next menu (config. not reset) Config. reset Confirmed Move to previous/next configuration menu Use this function to erase all previous system configuration settings and reset all configuration parameters back to the factory default values. This function is NOT reversible--be careful. Maintenance Menu (only displays if Sensing System is enabled) The Maintenance Menu will be displayed only if the optional AQL-CHEM is used and the Sensing System is enabled in the Chemistry Config. Wizard. This menu is used to perform functions relating to the AQL-CHEM ORP and pH sensing kit. pH Calibration Wizard, + to enter Push to access pH Calibration Wizard Move to previous/next menu item Use this Wizard to calibrate the AQL-CHEM's pH probe. This requires a manual pH test of the pool water using a dependable red phenol test kit. Clean Probe Wizard + to enter Push to access Clean Probe Wizard Move to previous/next menu item Use this Wizard to clean the AQL-CHEM's ORP and pH probes. The probes must be clean and free from oil, chemical deposits and contamination to function properly. Slow response, increased need to calibrate, and inconsistent readings are indications that the probes need to be cleaned. 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
40
VSP Speed
%
Toggle between % and RPM
Move to previous/next configuration menu
if any output is configured as a
variable speed pump
This is the unit of measure for displaying the speed of the variable speed pump.
Select % of maximum
speed (3450 RPM) or revolutions per minute (RPM).
Reset ColorLogic to
Default
Press +
Are you sure?
+ to proceed
ColorLogic. reset
Confirmed
Initiate reset of ColorLogic configuration parameters
Reset all configuration parameters
Move to previous/next configuration menu
(config. not reset)
Move to previous/next menu (config. not reset)
Move to previous/next configuration menu
if ColorLogic Network Module is detected
Use this function to erase all ColorLogic configuration settings and reset back to the factory default
values.
This function is NOT reversible--be careful.
Reset Config. to
Default
Press +
Are you sure?
+ to proceed
Config. reset
Confirmed
Initiate reset of all configuration parameters
Reset all configuration parameters
Move to previous/next configuration menu
(config. not reset)
Move to previous/next menu (config. not reset)
Move to previous/next configuration menu
Use this function to erase all previous system configuration settings and reset all configuration
parameters back to the factory default values.
This function is NOT reversible--be careful.
Maintenance Menu
(only displays if Sensing System is enabled)
The Maintenance Menu will be displayed only if the optional AQL-CHEM is used and the Sensing System is
enabled in the Chemistry Config. Wizard. This menu is used to perform functions relating to the AQL-CHEM ORP
and pH sensing kit.
pH Calibration
Wizard, + to enter
Push to access pH Calibration Wizard
Move to previous/next menu item
Use this Wizard to calibrate the AQL-CHEM’s pH probe.
This requires a manual pH test of the pool
water using a dependable red phenol test kit.
Clean Probe Wizard
+ to enter
Push to access Clean Probe Wizard
Move to previous/next menu item
Use this Wizard to clean the AQL-CHEM’s ORP and pH probes. The probes must be clean and free
from oil, chemical deposits and contamination to function properly.
Slow response, increased need to
calibrate, and inconsistent readings are indications that the probes need to be cleaned.