Hayward Pro Logic® Models: PL-PS-4 PL-PS-8 PL-PS-16 PL-PS-16V Installatio - Page 5

Installation Steps - pro logic 4 0

Get Hayward Pro Logic® PDF manuals and user guides View all Hayward Pro Logic® manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

NOTE: Before installing this product as part of a saline water purification system in a pool or spa using natural stone for coping or for immediately adjacent patios/decking, a qualified stone installation specialist should be consulted regarding the appropriate type, installation, sealant (if any) and maintenance of stone used around a saline pool with electronic chlorine generator in your particular location and circumstances. NOTE: The use of dry acid (sodium bisulfate) to adjust pool pH is discouraged especially in arid regions where pool water is subject to excessive evaporation and is not commonly diluted with fresh water. Dry acid can cause a buildup of by-products that can damage your chlorinator cell. Installation Steps Details on each installation step are presented on the following pages: 1. Prepare the pool water (page 3) General Water Chemistry Salt 2. Mounting the equipment (page 5) Pro Logic main unit Temperature sensors Remote display/keypad (optional) Valve actuators (if applicable) 3. Plumbing (page 8) General Pool Equipment Chlorinator Turbo Cell Flow Switch 4. Electrical Wiring (page 12) Main service Grounding and bonding Circuit breakers Pro Logic control power High Voltage pool equipment Low voltage wiring (temperature sensors, flow switch, etc.) 5. Pro Logic control configuration (program desired control operation) (page 22) 6. System Startup and checkout (page 41) 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
NOTE: Before installing this product as part of a saline water purification system in a pool or spa using natural
stone for coping or for immediately adjacent patios/decking, a qualified stone installation specialist should be
consulted regarding the appropriate type, installation, sealant (if any) and maintenance of stone used around a
saline pool with electronic chlorine generator in your particular location and circumstances.
NOTE: The use of dry acid (sodium bisulfate) to adjust pool pH is discouraged especially in arid regions where
pool water is subject to excessive evaporation and is not commonly diluted with fresh water. Dry acid can cause a
buildup of by-products that can damage your chlorinator cell.
Installation Steps
Details on each installation step are presented on the following pages:
1.
Prepare the pool water
(page 3)
General Water
Chemistry
Salt
2.
Mounting the equipment (page 5)
Pro Logic main unit
Temperature sensors
Remote display/keypad (optional)
Valve actuators (if applicable)
3.
Plumbing
(page 8)
General Pool Equipment
Chlorinator Turbo Cell
Flow Switch
4.
Electrical Wiring
(page 12)
Main service
Grounding and bonding
Circuit breakers
Pro Logic control power
High Voltage pool equipment
Low voltage wiring (temperature sensors, flow switch, etc.)
5.
Pro Logic control configuration (program desired control operation) (page 22)
6.
System Startup and checkout (page 41)
2