HP 11-p100 x360 Convertible PC model numbers 11-p100 through p199 Maintenance - Page 45

Power connector cable, as far as it will open.

Get HP 11-p100 PDF manuals and user guides View all HP 11-p100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Power connector cable Description Power connector cable Spare part number 755727-001 Before removing the power connector cable, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the bottom cover (see Bottom cover on page 23). 5. Remove the battery (see Battery on page 34). Remove the power connector cable: NOTE: The right bracket is also held in place by screws that were removed when the bottom cover was removed. 1. Remove the black Phillips PM2.5×6.0 screw (1) that secures the right bracket to the computer. 2. Open the display assembly right hinge (2) as far as it will open. 3. Remove the right hinge bracket from the computer (3). 4. Disconnect the power connector cable (4) from the system board. 5. Remove the power connector (5) from the computer. Reverse this procedure to install the power connector cable. Component replacement procedures 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Power connector cable
Description
Spare part number
Power connector cable
755727-001
Before removing the power connector cable, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
23
).
5.
Remove the battery (see
Battery
on page
34
).
Remove the power connector cable:
NOTE:
The right bracket is also held in place by screws that were removed when the bottom cover was
removed.
1.
Remove the black Phillips PM2.5×6.0 screw
(1)
that secures the right bracket to the computer.
2.
Open the display assembly right hinge
(2)
as far as it will open.
3.
Remove the right hinge bracket from the computer
(3)
.
4.
Disconnect the power connector cable
(4)
from the system board.
5.
Remove the power connector
(5)
from the computer.
Reverse this procedure to install the power connector cable.
Component replacement procedures
37