HP Cisco Catalyst Blade Switch 3020 Cisco Gigabit Ethernet Switch Module for H - Page 25

System Messages Guide, New System Messages

Page 25 highlights

Documentation Updates System Messages Guide These are the documentation updates for the system modesties guide: • New System Messages, page 25 • Changed System Messages, page 26 New System Messages These system messages have been added. Error Message DOT1X_SWITCH-5-ERR_ADDING_ADDRESS: Unable to add address [enet] on [chars] Explanation The client MAC address could not be added to the MAC address table because the hardware memory is full or the address is a secure address on another port. [enet] is the supplicant MAC address, and [chars] is the interface. This message might appear if the IEEE 802.1x feature is enabled. Recommended Action If the hardware memory is full, remove some of the dynamic MAC addresses. If the client address is on another port, manually remove it from that port. Error Message SPANTREE-6-PORTADD_ALL_VLANS: [chars] added to all Vlans Explanation The interface has been added to all VLANs. [chars] is the added interface. Recommended Action No action is required. Error Message SPANTREE-6-PORTDEL_ALL_VLANS: [chars] deleted from all Vlans Explanation The interface has been deleted from all VLANs. [chars] is the deleted interface. Recommended Action No action is required. Error Message SW_VLAN-6-VTP_DOMAIN_NAME_CHG: VTP domain name changed to [chars]. Explanation The VLAN Trunking Protocol (VTP) domain name was changed through the configuration to the name specified in the message. [chars] is the changed domain name. Recommended Action No action is required. Error Message VQPCLIENT-2-TOOMANY: Interface [chars] shutdown by active host limit. Explanation The system has shut down the specified interface because too many hosts have requested access to that interface. [chars] is the interface name. Recommended Action To enable the interface, remove the excess hosts, and enter the no shutdown interface configuration command. Cisco Gigabit Ethernet Switch Module for HP BladeSystem p-Class Release Notes, Cisco IOS Release 12.2(44)SE and Later 464831-005 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28

25
Cisco Gigabit Ethernet Switch Module for HP BladeSystem p-Class Release Notes, Cisco IOS Release 12.2(44)SE and Later
464831-005
Documentation Updates
System Messages Guide
These are the documentation updates for the system modesties guide:
New System Messages, page 25
Changed System Messages, page 26
New System Messages
These system messages have been added.
Error Message
DOT1X_SWITCH-5-ERR_ADDING_ADDRESS: Unable to add address [enet] on
[chars]
Explanation
The client MAC address could not be added to the MAC address table because the
hardware memory is full or the address is a secure address on another port. [enet] is the supplicant
MAC address, and [chars] is the interface. This message might appear if the IEEE 802.1x feature is
enabled.
Recommended Action
If the hardware memory is full, remove some of the dynamic MAC addresses.
If the client address is on another port, manually remove it from that port.
Error Message
SPANTREE-6-PORTADD_ALL_VLANS: [chars] added to all Vlans
Explanation
The interface has been added to all VLANs. [chars] is the added interface.
Recommended Action
No action is required.
Error Message
SPANTREE-6-PORTDEL_ALL_VLANS: [chars] deleted from all Vlans
Explanation
The interface has been deleted from all VLANs. [chars] is the deleted interface.
Recommended Action
No action is required.
Error Message
SW_VLAN-6-VTP_DOMAIN_NAME_CHG: VTP domain name changed to [chars].
Explanation
The VLAN Trunking Protocol (VTP) domain name was changed through the
configuration to the name specified in the message. [chars] is the changed domain name.
Recommended Action
No action is required.
Error Message
VQPCLIENT-2-TOOMANY: Interface [chars] shutdown by active host limit.
Explanation
The system has shut down the specified interface because too many hosts have requested
access to that interface. [chars] is the interface name.
Recommended Action
To enable the interface, remove the excess hosts, and enter the
no shutdown
interface configuration command.