HP Designjet L25500 HP Designjet L25500 Printer Series - User's guide (first e - Page 19

Handle the substrate, Overview, Use substrate - substrate edge not found

Get HP Designjet L25500 PDF manuals and user guides View all HP Designjet L25500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

4 Handle the substrate Handle the substrate Overview You can print on a wide variety of printing materials, all of which are referred to in this guide as substrates. Use substrate Choosing the correct substrate for your needs is an essential step in ensuring good print quality. For best printing results, use only recommended HP substrates (see Supported substrate families on page 16), which have been developed and thoroughly tested to ensure reliable performance. All printing components (printer, ink system, and substrate) have been designed to work together to offer trouble-free operation and ensure optimal print quality. Here are some additional tips about substrate usage: ● Allow all substrates to adapt to room conditions, out of the packaging, for 24 hours before using them for printing. ● Handle film and photo substrates by the edges, or wear cotton gloves. Skin oils can be transferred to the substrate, leaving fingerprint marks. ● Keep the substrate tightly wound on the roll throughout the loading and unloading procedures. To make sure that the roll stays tightly wound, consider using tape to stick the leading edge of the roll to the core just before removing the roll from the printer. You can keep the roll taped during storage. If the roll starts to unwind, it can become difficult to handle. NOTE: The use of tape to stick the leading edge of the roll to the core is especially important for heavy substrates, because the inherent stiffness of the substrate can cause it to loosen and unwind from the core. ● Whenever you load a roll, the front panel prompts you to specify the substrate family that you are loading. For good print quality, it is essential to specify this correctly. Check that the substrate belongs to the family named on the front panel, and check also that it matches the substrate profile in the RIP. ● Print quality could be impaired if you use a substrate that is unsuitable for your image. ● Make sure that the appropriate print-quality setting is selected in the RIP. ● If the substrate family shown on the front panel does not correspond to the substrate that you intend to use, take one of the following actions: ◦ Reload the roll into the printer and select the correct substrate family. See Unload a roll from the printer on page 22 and Load a roll into the printer on page 19. ◦ At the printer's front panel, select the icon, and then select View loaded substrate > Change loaded substrate. NOTE: Substrate advance calibration is not performed when the substrate family is changed from the front panel. ENWW Overview 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
4
Handle the substrate
Overview
You can print on a wide variety of printing materials, all of which are referred to in this guide as substrates.
Use substrate
Choosing the correct substrate for your needs is an essential step in ensuring good print quality. For
best printing results, use only recommended HP substrates (see
Supported substrate families
on page
16
), which have been developed and thoroughly tested to ensure reliable performance. All
printing components (printer, ink system, and substrate) have been designed to work together to offer
trouble-free operation and ensure optimal print quality.
Here are some additional tips about substrate usage:
●
Allow all substrates to adapt to room conditions, out of the packaging, for 24 hours before using
them for printing.
●
Handle film and photo substrates by the edges, or wear cotton gloves. Skin oils can be transferred
to the substrate, leaving fingerprint marks.
●
Keep the substrate tightly wound on the roll throughout the loading and unloading procedures. To
make sure that the roll stays tightly wound, consider using tape to stick the leading edge of the roll
to the core just before removing the roll from the printer. You can keep the roll taped during storage.
If the roll starts to unwind, it can become difficult to handle.
NOTE:
The use of tape to stick the leading edge of the roll to the core is especially important for
heavy substrates, because the inherent stiffness of the substrate can cause it to loosen and unwind
from the core.
●
Whenever you load a roll, the front panel prompts you to specify the substrate family that you are
loading. For good print quality, it is essential to specify this correctly. Check that the substrate
belongs to the family named on the front panel, and check also that it matches the substrate profile
in the RIP.
●
Print quality could be impaired if you use a substrate that is unsuitable for your image.
●
Make sure that the appropriate print-quality setting is selected in the RIP.
●
If the substrate family shown on the front panel does not correspond to the substrate that you intend
to use, take one of the following actions:
◦
Reload the roll into the printer and select the correct substrate family. See
Unload a roll from
the printer
on page
22
and
Load a roll into the printer
on page
19
.
◦
At the printer's front panel, select the
icon, and then select
View loaded substrate
>
Change loaded substrate
.
NOTE:
Substrate advance calibration is not performed when the substrate family is changed
from the front panel.
ENWW
Overview
15
Handle the substrate