HP Designjet L25500 HP Designjet L25500 Printer Series - User's guide (first e - Page 32

Take-up reel has been successfully installed, message appears. - with cutter

Get HP Designjet L25500 PDF manuals and user guides View all HP Designjet L25500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

15. Carefully insert the loop-shaping core. NOTE: Make sure that you insert the loop-shaping core. The take-up reel will not function correctly without it. The loop-shaping core must have end caps. Make sure that the end caps extend over the edges of the substrate. 16. Use the wind-direction switch on the take-up reel motor to select the winding direction. Setting 1 winds the substrate so that the printed image faces in. Setting 2 winds the substrate so that the printed image faces out. The front panel shows you the correct setting based on the winding-direction decision you made in step 7. Handle the substrate 17. Press the OK button on the front panel. The Take-up reel has been successfully installed message appears. 18. The following image shows how the printer looks when it is operating. As substrate is fed from the printer, it drops down in a loop and then up into the take-up reel spindle. NOTE: While the take-up reel is operating, make sure that the take-up reel sensors are not blocked. NOTE: The cutter is disabled when the take-up reel is in use. 28 Chapter 4 Handle the substrate ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
15.
Carefully insert the loop-shaping core.
NOTE:
Make sure that you insert the loop-shaping core. The take-up reel will not function
correctly without it. The loop-shaping core must have end caps. Make sure that the end caps extend
over the edges of the substrate.
16.
Use the wind-direction switch on the take-up reel motor to select the winding direction. Setting
1
winds the substrate so that the printed image faces in. Setting
2
winds the substrate so that the
printed image faces out.
The front panel shows you the correct setting based on the winding-direction decision you made
in step 7.
17.
Press the
OK
button on the front panel. The
Take-up reel has been successfully installed
message appears.
18.
The following image shows how the printer looks when it is operating. As substrate is fed from the
printer, it drops down in a loop and then up into the take-up reel spindle.
NOTE:
While the take-up reel is operating, make sure that the take-up reel sensors are not blocked.
NOTE:
The cutter is disabled when the take-up reel is in use.
28
Chapter 4
Handle the substrate
ENWW
Handle the substrate