HP Designjet L25500 HP Designjet L25500 Printer Series - User's guide (first e - Page 64

Print options, Printer states, Change margins

Get HP Designjet L25500 PDF manuals and user guides View all HP Designjet L25500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Print options 6 Print options Printer states The printer may be in any one of the following states; some of them require waiting. ● Ready (cold): The printer is powered on but has not printed yet, and the heaters are not turned on. ● Preparing to print: The printer is warming up the heaters and preparing the printheads to print. This takes 1 to 8 min. ● Printing ● Curing: This takes 1.5 to 5 min. ● Finishing: The printer is cooling down and preparing for stand-by. This takes 0.5 to 5 min. ● Ready (hot): The printer is ready and the heaters are in stand-by. ◦ If a new job arrives the printer goes to Preparing to print. ◦ If there is no new job in a period of 10 minutes, the heaters turn off and the printer goes to Ready (cold). If jobs of the same print mode as the already-printed file are sent while the printer is Curing (if the cutter is not enabled) or Finishing, the printer goes to Preparing to print. To save time between prints, concatenate jobs with the same print mode (same number of passes) and turn the cutter off to skip the Curing and Finishing states. You can also use nesting to print several jobs in the same workflow. Even if the cutter is on or successive jobs use different print modes, it is better to print them all together without delays to minimize the time spent in Preparing to print. Change margins The printer margins determine the area between the edges of your image and the edges of the substrate. The margins for a particular print job are selected in the RIP software; if the job exceeds the substrate width, it will be clipped. In addition, the front panel offers three settings for the bottom margin: normal, small and extended; see Table 8-4 Margins on page 63. This selection only applies to single prints when the cutter is not in use. The bottom margin is not applied between several prints sent at the same time. To set the bottom margin at the front panel, select the icon, and then Substrate handling options > Extra bottom margin. NOTE: If a larger margin is set in the RIP, it overrides the bottom margin set in the front panel. 60 Chapter 6 Print options ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
6
Print options
Printer states
The printer may be in any one of the following states; some of them require waiting.
●
Ready (cold)
: The printer is powered on but has not printed yet, and the heaters are not turned
on.
●
Preparing to print
: The printer is warming up the heaters and preparing the printheads to print.
This takes 1 to 8 min.
●
Printing
●
Curing
: This takes 1.5 to 5 min.
●
Finishing
: The printer is cooling down and preparing for stand-by. This takes 0.5 to 5 min.
●
Ready (hot)
: The printer is ready and the heaters are in stand-by.
◦
If a new job arrives the printer goes to
Preparing to print
.
◦
If there is no new job in a period of 10 minutes, the heaters turn off and the printer goes to
Ready (cold)
.
If jobs of the same print mode as the already-printed file are sent while the printer is
Curing
(if the cutter
is not enabled) or
Finishing
, the printer goes to
Preparing to print
.
To save time between prints, concatenate jobs with the same print mode (same number of passes) and
turn the cutter off to skip the
Curing
and
Finishing
states. You can also use nesting to print several
jobs in the same workflow.
Even if the cutter is on or successive jobs use different print modes, it is better to print them all together
without delays to minimize the time spent in
Preparing to print
.
Change margins
The printer margins determine the area between the edges of your image and the edges of the substrate.
The margins for a particular print job are selected in the RIP software; if the job exceeds the substrate
width, it will be clipped.
In addition, the front panel offers three settings for the bottom margin: normal, small and extended;
see
Table
8
-
4
Margins
on page
63
. This selection only applies to single prints when the cutter is not
in use. The bottom margin is not applied between several prints sent at the same time.
To set the bottom margin at the front panel, select the
icon, and then
Substrate handling options
>
Extra bottom margin
.
NOTE:
If a larger margin is set in the RIP, it overrides the bottom margin set in the front panel.
60
Chapter 6
Print options
ENWW
Print options