HP Designjet L25500 HP Designjet L25500 Printer Series - User's guide (first e - Page 26

Unload a roll from the printer, The normal procedure (roll attached to spindle)

Get HP Designjet L25500 PDF manuals and user guides View all HP Designjet L25500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Unload a roll from the printer If you used the take-up reel during printing, unload the printed roll from the take-up reel before attempting to remove the roll from the printer. See Unload a roll from the take-up reel on page 29. Check whether the other end of the roll is still attached to the input spindle, and follow the appropriate procedure as described in the following sections. The normal procedure (roll attached to spindle) If the end of the roll is still attached to the spindle, use the following procedure. 1. On the printer's front panel, select the icon, and then select Substrate unload > Unload roll. 2. Press the OK button on the front panel as many times as needed to rewind the substrate. 3. Lift the spindle lock lever. 4. Remove the roll from the printer, pulling out the right end on the right side of the printer first. Do not insert your fingers into the spindle supports during the removal process. Exceptional procedure (roll detached from spindle) Use the following procedure if the end of the roll is visible but no longer attached to the spindle: 1. If you have already selected Substrate unload at the front panel, press the Cancel button to cancel that procedure. 2. Lift the substrate-adjustment lever. If the front panel shows a warning about the lever, ignore it. Handle the substrate 22 Chapter 4 Handle the substrate ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
Unload a roll from the printer
If you used the take-up reel during printing, unload the printed roll from the take-up reel before attempting
to remove the roll from the printer. See
Unload a roll from the take-up reel
on page
29
.
Check whether the other end of the roll is still attached to the input spindle, and follow the appropriate
procedure as described in the following sections.
The normal procedure (roll attached to spindle)
If the end of the roll is still attached to the spindle, use the following procedure.
1.
On the printer's front panel, select the
icon, and then select
Substrate unload
>
Unload roll
.
2.
Press the
OK
button on the front panel as many times as needed to rewind the substrate.
3.
Lift the spindle lock lever.
4.
Remove the roll from the printer, pulling out the right end on the right side of the printer first. Do
not insert your fingers into the spindle supports during the removal process.
Exceptional procedure (roll detached from spindle)
Use the following procedure if the end of the roll is visible but no longer attached to the spindle:
1.
If you have already selected
Substrate unload
at the front panel, press the
Cancel
button to cancel
that procedure.
2.
Lift the substrate-adjustment lever. If the front panel shows a warning about the lever, ignore it.
22
Chapter 4
Handle the substrate
ENWW
Handle the substrate