HP Designjet L25500 HP Designjet L25500 Printer Series - User's guide (first e - Page 5

Introduction, Safety precautions, General safety guidelines, Electrical shock hazard - supplies

Get HP Designjet L25500 PDF manuals and user guides View all HP Designjet L25500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Introduction 1 Introduction Safety precautions Before using your printer, read the following safety precautions to make sure you use the equipment safely. General safety guidelines ● Refer to installation instructions before connecting the printer to the supply. ● There are no operator-serviceable parts inside the printer. Refer servicing to qualified service personnel. ● Turn off the printer, unplug both power cords from the power outlets, and call your service representative in any of the following cases: ◦ The power cord or plug is damaged. ◦ Liquid has entered the printer. ◦ There is smoke or an unusual smell coming from the printer. ◦ The printer has been dropped or the drying or curing module damaged. ◦ The printer's built-in Residual Current Circuit Breaker (Ground Fault Circuit Interrupter) has been repeatedly tripped. ◦ Fuses have blown. ◦ The printer is not operating normally. ● Turn off the printer and unplug both power cords from the power outlets in either of the following cases: ◦ During a thunderstorm ◦ During a power failure Electrical shock hazard WARNING! The drying and curing modules operate at hazardous voltages capable of causing death or serious personal injury. The printer uses two power cords. Unplug both power cords before servicing the printer. The printer must be connected to earthed mains outlets only. ENWW Safety precautions 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
1
Introduction
Safety precautions
Before using your printer, read the following safety precautions to make sure you use the equipment
safely.
General safety guidelines
●
Refer to installation instructions before connecting the printer to the supply.
●
There are no operator-serviceable parts inside the printer. Refer servicing to qualified service
personnel.
●
Turn off the printer, unplug both power cords from the power outlets, and call your service
representative in any of the following cases:
◦
The power cord or plug is damaged.
◦
Liquid has entered the printer.
◦
There is smoke or an unusual smell coming from the printer.
◦
The printer has been dropped or the drying or curing module damaged.
◦
The printer's built-in Residual Current Circuit Breaker (Ground Fault Circuit Interrupter) has
been repeatedly tripped.
◦
Fuses have blown.
◦
The printer is not operating normally.
●
Turn off the printer and unplug both power cords from the power outlets in either of the following
cases:
◦
During a thunderstorm
◦
During a power failure
Electrical shock hazard
WARNING!
The drying and curing modules operate at hazardous voltages capable of causing death
or serious personal injury.
The printer uses two power cords. Unplug both power cords before servicing the printer. The printer
must be connected to earthed mains outlets only.
ENWW
Safety precautions
1
Introduction