HP ENVY 14t-3000 HP ENVY14 SPECTRE Maintenance and Service Guide IMPORTANT! Th - Page 53

Power button board, Remove the Card Reader board

Get HP ENVY 14t-3000 PDF manuals and user guides View all HP ENVY 14t-3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Remove the Card Reader board: 1. Turn the top cover upside down, with the front toward you. 2. Remove the two Phillips PM2.0×3.6 screws (1) and the Phillips PM2.0×3.2 screw (2) that secure the Card Reader board to the top cover. 3. Lift the left side of the Card Reader board (3) until it rests at an angle. 4. Remove the Card Reader board (4) by sliding it up and to the left at an angle. Reverse this procedure to install the Card Reader board. Power button board Description Power button board (includes cable) Spare part number 675510-001 Before removing the power button board, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. Component replacement procedures 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
Remove the Card Reader board:
1.
Turn the top cover upside down, with the front toward you.
2.
Remove the two Phillips PM2.0×3.6 screws
(1)
and the Phillips PM2.0×3.2 screw
(2)
that secure
the Card Reader board to the top cover.
3.
Lift the left side of the Card Reader board
(3)
until it rests at an angle.
4.
Remove the Card Reader board
(4)
by sliding it up and to the left at an angle.
Reverse this procedure to install the Card Reader board.
Power button board
Description
Spare part number
Power button board (includes cable)
675510-001
Before removing the power button board, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
Component replacement procedures
45