HP ENVY 14t-3000 HP ENVY14 SPECTRE Maintenance and Service Guide IMPORTANT! Th - Page 68

Heat sink

Get HP ENVY 14t-3000 PDF manuals and user guides View all HP ENVY 14t-3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

3. Remove the memory module (2) by pulling it away from the slot at an angle. Reverse this procedure to install the memory module. Heat sink NOTE: The heat sink spare part kits include replacement thermal material. Description Processor heat sink Post controller hub heat sink Thermal Material Kit (includes replacement thermal material) Spare part number 675514-001 685662-001 675515-001 Before removing the heat sink, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the battery (see Battery on page 32), and then remove the following components: a. Solid-state drive connector board cable (see Solid-state drive on page 34) b. Card Reader board cable (see Card Reader board cable on page 36) c. Top cover (see Top cover on page 39) d. WLAN module (see WLAN module on page 52) 60 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
3.
Remove the memory module
(2)
by pulling it away from the slot at an angle.
Reverse this procedure to install the memory module.
Heat sink
NOTE:
The heat sink spare part kits include replacement thermal material.
Description
Spare part number
Processor heat sink
675514-001
Post controller hub heat sink
685662-001
Thermal Material Kit (includes replacement thermal material)
675515-001
Before removing the heat sink, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see
Battery
on page
32
), and then remove the following components:
a.
Solid-state drive connector board cable (see
Solid-state drive
on page
34
)
b.
Card Reader board cable (see
Card Reader board cable
on page
36
)
c.
Top cover (see
Top cover
on page
39
)
d.
WLAN module (see
WLAN module
on page
52
)
60
Chapter 4
Removal and replacement procedures