HP ENVY 15-as100 Maintenance and Service Guide - Page 50

Power connector cable, from the system board.

Get HP ENVY 15-as100 PDF manuals and user guides View all HP ENVY 15-as100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Reverse this procedure to install the TouchPad. Power connector cable Description Power connector cable Spare part number 857438-010 Before removing the power connector cable, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the bottom cover (see Bottom cover on page 28). 5. Disconnect the battery cable from the system board (see Battery on page 31). Remove the power connector cable: 1. Remove the four Phillips M2.5×5.8 screws (1) that secure the right display hinge to the keyboard/ top cover. 2. Swing the right display hinge (2) up and back until the power connector is accessible. 3. Disconnect the power connector cable (1) from the system board. 4. Remove the three Phillips M2.5×3.8 screws (2) that secure the power connector cable bracket to the keyboard/top cover. 5. Remove the power connector cable bracket (3). The power connector cable bracket is included in the I/O Bracket Kit, spare part number 857795-001. 42 Chapter 5 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Reverse this procedure to install the TouchPad.
Power connector cable
Description
Spare part number
Power connector cable
857438-010
Before removing the power connector cable, follow these steps:
1.
Turn
off
the computer. If you are unsure whether the computer is
off
or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
28
).
5.
Disconnect the battery cable from the system board (see
Battery
on page
31
).
Remove the power connector cable:
1.
Remove the four Phillips M2.5×5.8 screws
(1)
that secure the right display hinge to the keyboard/
top cover.
2.
Swing the right display hinge
(2)
up and back until the power connector is accessible.
3.
Disconnect the power connector cable
(1)
from the system board.
4.
Remove the three Phillips M2.5×3.8 screws
(2)
that secure the power connector cable bracket to
the keyboard/top cover.
5.
Remove the power connector cable bracket
(3)
.
The power connector cable bracket is included in the I/O Bracket Kit, spare part number 857795-001.
42
Chapter 5
Removal and replacement procedures