HP ENVY m6-n012dx HP ENVY m6 Notebook PC Maintenance and Service Guide - Page 77

Connector board, Disconnect the connector board cable

Get HP ENVY m6-n012dx PDF manuals and user guides View all HP ENVY m6-n012dx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Connector board NOTE: The connector board spare part kit includes the audio jack, RJ-45 jack, USB port, and 2 cables. Description Spare part number For use only on computer models equipped with an AMD processor 760038-001 For use only on computer models equipped with an Intel processor and a graphics subsystem with 765146-001 discrete memory For use only on computer models equipped with an Intel processor and a graphics subsystem with 765145-001 UMA memory Before removing the connector board, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the battery (see Battery on page 37), and then remove the following components: a. Service cover (see WLAN module on page 38) b. Hard drive (see Hard drive on page 41) c. Base enclosure (see Base enclosure on page 48) Remove the connector board: 1. Disconnect the connector board cable (1) from the system board. 2. Release the connector board cable from the retention clips built into the top cover (2) and the subwoofer (3). 3. Release the ZIF connector (4) to which the connector board ribbon cable is attached, and then disconnect the connector board ribbon cable from the system board. Component replacement procedures 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Connector board
NOTE:
The connector board spare part kit includes the audio jack, RJ-45 jack, USB port, and 2
cables.
Description
Spare part number
For use only on computer models equipped with an AMD processor
760038-001
For use only on computer models equipped with an Intel processor and a graphics subsystem with
discrete memory
765146-001
For use only on computer models equipped with an Intel processor and a graphics subsystem with
UMA memory
765145-001
Before removing the connector board, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see
Battery
on page
37
), and then remove the following components:
a.
Service cover (see
WLAN module
on page
38
)
b.
Hard drive (see
Hard drive
on page
41
)
c.
Base enclosure (see
Base enclosure
on page
48
)
Remove the connector board:
1.
Disconnect the connector board cable
(1)
from the system board.
2.
Release the connector board cable from the retention clips built into the top cover
(2)
and the
subwoofer
(3)
.
3.
Release the ZIF connector
(4)
to which the connector board ribbon cable is attached, and then
disconnect the connector board ribbon cable from the system board.
Component replacement procedures
69