HP ENVY m7-u100 Maintenance and Service Guide - Page 39

Hard drive, to which the hard drive cable is connected, and then

Get HP ENVY m7-u100 PDF manuals and user guides View all HP ENVY m7-u100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Hard drive Description Spare part number 1-TB, 5400-rpm, SATA, 7.2-mm hard drive NOTE: The hard drive spare part kit does not include the hard drive rubber bracket or hard drive cable. The hard drive rubber bracket is available using spare part number 857826-001. The hard drive cable is available using spare part number 857835-001. 766457-856 Before removing the hard drive, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the bottom cover (see Bottom cover on page 24). 5. Disconnect the battery cable from the system board (see Battery on page 26). Remove the hard drive: 1. Release the zero insertion force (ZIF) connector (1) to which the hard drive cable is connected, and then disconnect the hard drive cable (2) from the system board. 2. Lift the right side of the hard drive (3) until it rests at an angle. 3. Remove the hard drive (4). 4. If it is necessary to replace the hard drive cable, disconnect the cable (1) from the hard drive. Component replacement procedures 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Hard drive
Description
Spare part number
1-TB, 5400-rpm, SATA, 7.2-mm hard drive
NOTE:
The hard drive spare part kit does not include the hard drive rubber bracket or hard drive cable.
The hard drive rubber bracket is available using spare part number 857826-001. The hard drive cable is
available using spare part number 857835-001.
766457-856
Before removing the hard drive, follow these steps:
1.
Turn
off
the computer. If you are unsure whether the computer is
off
or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
24
).
5.
Disconnect the battery cable from the system board (see
Battery
on page
26
).
Remove the hard drive:
1.
Release the zero insertion force (ZIF) connector
(1)
to which the hard drive cable is connected, and then
disconnect the hard drive cable
(2)
from the system board.
2.
Lift the right side of the hard drive
(3)
until it rests at an angle.
3.
Remove the hard drive
(4)
.
4.
If it is necessary to replace the hard drive cable, disconnect the cable
(1)
from the hard drive.
Component replacement procedures
31