HP ENVY m7-u100 Maintenance and Service Guide - Page 56

Display assembly, from the terminals on the WLAN module.

Get HP ENVY m7-u100 PDF manuals and user guides View all HP ENVY m7-u100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Reverse this procedure to install the speakers. Display assembly Description 17.3-in, UHD, WLED, AntiGlare (3840×2160), uslim-flat (2.68-mm), UWVA, eDP+PSR TouchScreen display assembly equipped with HDC and webcam 17.3-in, FHD, WLED, BrightView (1920×1080), slim-flat (3.0-mm), UWVA, eDP TouchScreen display assembly equipped with HDC and webcam Spare part number 859440-001 859439-001 Before removing the display assembly, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the bottom cover (see Bottom cover on page 24). 5. Disconnect the battery cable from the system board (see Battery on page 26). Remove the display assembly: 1. Release the ZIF connector (1) to which the display panel cable is connected, and then disconnect the display panel cable from the system board. 2. Release the ZIF connector (2) to which the webcam/microphone module cable is connected, and then disconnect the webcam/microphone module cable from the system board. 3. Disconnect the WLAN antenna cables (3) from the terminals on the WLAN module. NOTE: The WLAN antenna cable labeled "1/MAIN" connects to the WLAN module "Main" terminal. The WLAN antenna cable labeled "2/AUX" connects to the WLAN module "Aux" terminal. 4. Remove the four Phillips M2.0×4.8 screws (1) and the Phillips M2.0×3.8 screw (2) that secure the power connector cable bracket and the USB board bracket to the keyboard/top cover. 48 Chapter 5 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Reverse this procedure to install the speakers.
Display assembly
Description
Spare part number
17.3-in, UHD, WLED, AntiGlare (3840×2160),
uslim-flat
(2.68-mm), UWVA, eDP+PSR TouchScreen
display assembly equipped with HDC and webcam
859440-001
17.3-in, FHD, WLED, BrightView (1920×1080),
slim-flat
(3.0-mm), UWVA, eDP TouchScreen display
assembly equipped with HDC and webcam
859439-001
Before removing the display assembly, follow these steps:
1.
Turn
off
the computer. If you are unsure whether the computer is
off
or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
24
).
5.
Disconnect the battery cable from the system board (see
Battery
on page
26
).
Remove the display assembly:
1.
Release the ZIF connector
(1)
to which the display panel cable is connected, and then disconnect
the display panel cable from the system board.
2.
Release the ZIF connector
(2)
to which the webcam/microphone module cable is connected, and then
disconnect the webcam/microphone module cable from the system board.
3.
Disconnect the WLAN antenna cables
(3)
from the terminals on the WLAN module.
NOTE:
The WLAN antenna cable labeled “1/MAIN” connects to the WLAN module “Main” terminal.
The WLAN antenna cable labeled “2/AUX” connects to the WLAN module “Aux” terminal.
4.
Remove the four Phillips M2.0×4.8 screws
(1)
and the Phillips M2.0×3.8 screw
(2)
that secure the power
connector cable bracket and the USB board bracket to the keyboard/top cover.
48
Chapter 5
Removal and replacement procedures