HP Kayak XU 04xx HP Kayak XU PC Workstation Technical Reference Manual Hardwar - Page 49

BT/100TX LAN Controller, HP Kayak XU PC Workstation, User's, Guide, User's Guide

Get HP Kayak XU 04xx PDF manuals and user guides View all HP Kayak XU 04xx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

3 Interface Boards and Mass-Storage Drives 10BT/100TX LAN Controller 10BT/100TX LAN Controller Certain models of the HP Kayak XU PC Workstation are supplied only with a 10BT/100TX LAN adapter which supports the following standards: 100 Mbits per second over 2-pair, category-5, unshielded twisted pair (UTP), or shielded twisted pair (STP); 10 BaseT, 10 Mbits per second, ISO 8802-3 (IEEE 802.3 standard). On the rear panel there is one RJ-45 connector. There is an LED which indicates the LAN connection status as follows: • Off - when there is no Autonegotiation response (for example, when the LAN cable is not connected to the network HUB. • Blinking - during Autonegotiation • Green (ON) - the connection has passed the Autonegotiation and a link has been established between the LAN adapter and the network HUB/ Switch. The LAN adapter contains a connector to which an internal LAN cable may be connected to the external start connector on the system board, necessary for the use of the Remote Power On feature, described in detail in the User's Guide provided with the PC Workstation. The LAN adapter that uses the Remote Power On feature must be installed nearer the processors than any other supplementary LAN adapter card. Internal LAN connector for External Start (Remote On) Optional ROM Socket NOTE LAN cable connector (RJ-45) Refer to the User's Guide for details concerning system configuration changes necessary after installing a LAN adapter. 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
41
3
Interface Boards and Mass-Storage Drives
10BT/100TX LAN Controller
10BT/100TX LAN Controller
Certain models of the
HP Kayak XU PC Workstation
are supplied only with
a 10BT/100TX LAN adapter which supports the following standards:
100 Mbits per second over 2-pair, category-5, unshielded twisted pair
(UTP), or shielded twisted pair (STP); 10 BaseT, 10 Mbits per second, ISO
8802-3 (IEEE 802.3 standard).
On the rear panel there is one RJ-45 connector. There is an LED which
indicates the LAN connection status as follows:
•
Off - when there is no Autonegotiation response (for example, when the
LAN cable is not connected to the network HUB.
•
Blinking - during Autonegotiation
•
Green (ON) - the connection has passed the Autonegotiation and a link
has been established between the LAN adapter and the network HUB/
Switch.
The LAN adapter contains a connector to which an internal LAN cable may
be connected to the external start connector on the system board, necessary
for the use of the Remote Power On feature, described in detail in the
User’s
Guide
provided with the PC Workstation. The LAN adapter that uses the
Remote Power On feature must be installed nearer the processors than any
other supplementary LAN adapter card.
NOTE
Refer to the
User’s Guide
for details concerning system configuration
changes necessary after installing a LAN adapter.
Internal LAN connector for External
Start (Remote On)
LAN cable connector (RJ-45)
Optional ROM Socket