HP LH4r HP Netserver LH 3000 Rack Cabling Guide - Page 12

Prepare Rack Enclosures for Assembly

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Chapter 1 Preparation for Cabling the HP NetServer LH 3000r 3. Prepare Rack Enclosures for Assembly WARNING A tip-over hazard exists. Rack enclosures are shipped upright and are top-heavy. Never move enclosures without adequate equipment and assistance. Use caution to prevent rack from falling over and causing potential damage or injury. If you receive pre-configured units, follow assembly instructions from the supplying organization first, if you have them. Otherwise, continue with this set of instructions. 4. Move Rack Enclosures and Other Units to Installation Location WARNING Whenever you lift equipment, limit the amount of weight each person picks up. Lift with your legs, not with your back. Use two or more people and the proper equipment to move the rack enclosure, server, mass storage units, and other components. Stage cartons a few feet from your assembly and final power-up location. 5. Unpack Rack Enclosures and Hardware, Use Anti-Tip Measures, and Remove the Shipping Panels WARNING Use care in moving the rack down from the pallet. Three people are required for this step. 1. Follow any pictorial instructions on the outside of the shipping container to unbox the rack enclosure. 2. Adjust the leveler screws, when present, under each of the four corners of each rack. Lower each leveler screw to be in firm contact with the floor. CAUTION The leveler screws prevent the rack from rolling away when you install components. Be sure to lower these screws before you put anything into the rack. 3. Find and extend the anti-tip foot under the rack (or bolt on the anti-tip mechanism, if included) before you mount any rack equipment on slides. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
Chapter 1
Preparation for Cabling the HP NetServer LH 3000r
8
3.
Prepare Rack Enclosures for Assembly
WARNING
A tip-over hazard exists. Rack enclosures are shipped upright
and are top-heavy. Never move enclosures without adequate
equipment and assistance. Use caution to prevent rack from
falling over and causing potential damage or injury.
If you receive pre-configured units, follow assembly instructions from the
supplying organization first, if you have them. Otherwise, continue with this set of
instructions.
4.
Move Rack Enclosures and Other Units to Installation Location
WARNING
Whenever you lift equipment, limit the amount of weight each
person picks up. Lift with your legs, not with your back.
Use two or more people and the proper equipment to move the rack enclosure,
server, mass storage units, and other components. Stage cartons a few feet from
your assembly and final power-up location.
5.
Unpack Rack Enclosures and Hardware, Use Anti-Tip Measures, and Remove
the Shipping Panels
WARNING
Use care in moving the rack down from the pallet. Three
people are required for this step.
1.
Follow any pictorial instructions on the outside of the shipping container to
unbox the rack enclosure.
2.
Adjust the leveler screws, when present, under each of the four corners of
each rack. Lower each leveler screw to be in firm contact with the floor.
CAUTION
The leveler screws prevent the rack from rolling away when
you install components. Be sure to lower these screws before
you put anything into the rack.
3.
Find and extend the anti-tip foot under the rack (or bolt on the anti-tip
mechanism, if included) before you mount any rack equipment on slides.