HP Model 748 HP Model 748 Service Handbook - Page 63

Removing and Replacing Mass Storage Devices, Contents, Introduction, Preliminary Requirements

Get HP Model 748 - VME Workstation PDF manuals and user guides View all HP Model 748 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Removing and Replacing Mass Storage Devices Removing and Replacing Mass Storage Devices Section Contents • Removing the Mass Storage Module • Removal and replacement instructions for mass storage devices • Device addressing and location Introduction Instructions for removing and replacing Mass Storage Devices (internal) are in this section. The procedures for all devices are the same. Devices include the following: 3.5-inch Flexible Disk Drive Hard Disk Drives CD-ROM Drive DDS Tape Drive Preliminary Requirements Before you remove the Mass Storage Module perform the following: 1 Before system shut down is performed you should execute ioscan, and record the SCSI addresses in-use. 2 Shut down any applications. 3 Shut down the Operating System. 4 Refer to the owner's guide, for information on properly shutting down HP-UX. 5 Turn off power to the Model 748. 6 Set up a static-free work place to handle the mass storage tray. 5-15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Removing and Replacing Mass Storage Devices
5-15
Removing and Replacing Mass Storage Devices
Section Contents
•
Removing the Mass Storage Module
•
Removal and replacement instructions for mass storage devices
•
Device addressing and location
Introduction
Instructions for removing and replacing Mass Storage Devices (internal) are in this sec-
tion. The procedures for all devices are the same. Devices include the following:
3.5-inch Flexible Disk Drive
Hard Disk Drives
CD-ROM Drive
DDS Tape Drive
Preliminary Requirements
Before you remove the Mass Storage Module perform the following:
1
Before system shut down is performed you should execute
ioscan
, and record the SCSI
addresses in-use.
2
Shut down any applications.
3
Shut down the Operating System.
4
Refer to the owner’s guide, for information on properly shutting down HP-UX.
5
Turn off power to the Model 748.
6
Set up a static-free work place to handle the mass storage tray.