HP Model 755/125cL hp DDS-2 tape drive user's guide (a1658-90689) - Page 39

Checking the Hardware Installation

Get HP Model 755/125cL - Workstation PDF manuals and user guides View all HP Model 755/125cL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Troubleshooting and Removal/Replacement Procedures 8/12 8/12/5 8/12/5.3 8/12/5.3.0 8/12/5.4 8/12/5.4.0 8/12/5.6 8/12/5.6.0 10 10/12 10/12.4 10/12.4.0 ba ext_bus target tape target disk target disk bc ext_bus target disk Core I/O Adapter Built-in SCSI HP C1533A SEAGATE ST3600N MICROP 2112 I/O Adapter GSC add-on Fast/Wide SCSI Interface SEAGATE ST31200W Checking the Hardware Installation Perform the following steps to check the hardware installation: CAUTION: The DDS-2 drive is susceptible to mechanical and electrostatic shock. When handling the drive, always wear the static strap that came in the DDS-2 drive kit. Always handle the drive carefully. 1. Check that the SCSI-2 terminator is connected to the single-ended SCSI-2 port on the rear I/O panel of the system unit (if there are no external SCSI-2 devices), or that the last external single-ended SCSI-2 device is terminated. 2. Attach the static-grounding wrist strap by following the instructions on the package that contains the strap. 3. Shut down HP-UX. NOTICE: If you are already at the boot administration level, you do not need to shut down; skip this step and go on to Step 4. If you are running HP-UX under HP VUE, shut down your system by performing the shutdown procedure described in the Owner's Guide that came with your workstation. 3-4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
Troubleshooting and Removal/Replacement Procedures
3–4
8/12
ba
Core I/O Adapter
8/12/5
ext_bus
Built-in SCSI
8/12/5.3
target
8/12/5.3.0
tape
HP C1533A
8/12/5.4
target
8/12/5.4.0
disk
SEAGATE ST3600N
8/12/5.6
target
8/12/5.6.0
disk
MICROP
2112
10
bc
I/O Adapter
10/12
ext_bus
GSC add-on Fast/Wide SCSI Interface
10/12.4
target
10/12.4.0
disk
SEAGATE ST31200W
Checking the Hardware Installation
Perform the following steps to check the hardware installation:
CAUTION:
The DDS-2 drive is susceptible to mechanical and electrostatic
shock. When handling the drive, always wear the static strap that
came in the DDS-2 drive kit. Always handle the drive carefully.
1.
Check that the SCSI-2 terminator is connected to the single-ended SCSI-2 port on
the rear I/O panel of the system unit (if there are no external SCSI-2 devices), or
that the last external single-ended SCSI-2 device is terminated.
2.
Attach the static-grounding wrist strap by following the instructions on the package
that contains the strap.
3.
Shut down HP-UX.
NOTICE:
If you are already at the boot administration level, you do not need
to shut down; skip this step and go on to Step 4.
If you are running HP-UX under HP VUE, shut down your system by performing
the shutdown procedure described in the Owner’s Guide that came with your work-
station.