HP ProLiant SL4545 HP ProLiant SL4500 Series Setup and Installation Guide - Page 37

Cabling and powering up the chassis, Cabling the chassis, Installing the cable management arm

Get HP ProLiant SL4545 PDF manuals and user guides View all HP ProLiant SL4545 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Cabling and powering up the chassis Cabling the chassis After all system hardware is installed, cable the components. See the HP ProLiant SL Servers Site Planning Guide on the Documentation CD or the HP website (http://www.hp.com) for additional cabling and site planning requirements. WARNING: To reduce the risk of electric shock or injury due to high-current electrical energy, be sure that all power is completely disconnected at the source before beginning any power connections to the power bus bars or power bus box. WARNING: Be sure that all circuit breakers are locked in the off position before connecting any power components. CAUTION: To avoid damaging the fiber cables, do not drape cables from one side of the rack to the other and do not run cables over a hard corner or edge. To cable the system: 1. Connect the network cables to the Ethernet ports on the I/O module ("I/O module connectors and LEDs" on page 13). 2. Connect a network cable to the iLO connector on the management module ("Management module connectors and LEDs" on page 15). 3. Connect a SL-APM cable to the SL-APM connector on the management module ("Management module connectors and LEDs" on page 15). Installing the cable management arm IMPORTANT: If you need to hinge the cable management arm on the rear right-hand side of the rack, see the instructions in "Converting the cable management arm for opposite side mounting." Perform these steps to convert the arm to a right-hand swing and install the arm on the right side of the rack. Cabling and powering up the chassis 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Cabling and powering up the chassis
37
Cabling and powering up the chassis
Cabling the chassis
After all system hardware is installed, cable the components. See the
HP ProLiant SL Servers Site Planning
Guide
on the Documentation CD or the HP website (
) for additional cabling and site
planning requirements.
WARNING:
To reduce the risk of electric shock or injury due to high-current electrical energy, be
sure that all power is completely disconnected at the source before beginning any power
connections to the power bus bars or power bus box.
WARNING:
Be sure that all circuit breakers are locked in the off position before connecting any
power components.
CAUTION:
To avoid damaging the fiber cables, do not drape cables from one side of the rack
to the other and do not run cables over a hard corner or edge.
To cable the system:
1.
Connect the network cables to the Ethernet ports on the I/O module ("
I/O module connectors and LEDs
"
on page
13
).
2.
Connect a network cable to the iLO connector on the management module ("
Management module
connectors and LEDs
" on page
15
).
3.
Connect a SL-APM cable to the SL-APM connector on the management module ("
Management module
connectors and LEDs
" on page
15
).
Installing the cable management arm
IMPORTANT:
If you need to hinge the cable management arm on the rear right-hand side of the
rack, see the instructions in "Converting the cable management arm for opposite side mounting."
Perform these steps to convert the arm to a right-hand swing and install the arm on the right side
of the rack.