HP Spectre Ultrabook 14-3200 HP Spectre Ultrabook PC Maintenance and Service G - Page 49

from the TouchPad., the TouchPad cable

Get HP Spectre Ultrabook 14-3200 PDF manuals and user guides View all HP Spectre Ultrabook 14-3200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

5. Remove the solid-state drive connector board cable (see Solid-state drive on page 35). 6. Remove the Card Reader board cable (see Card Reader board cable on page 37). NOTE: When replacing the top cover, be sure to remove the following components from the defective top cover and install them on the replacement top cover: ● NFC board (see NFC board on page 38) ● Solid-state drive connector board (see Card Reader board cable on page 37) ● Card Reader board (see Card Reader board on page 45) ● Power button board (see Power button board on page 46) Remove the top cover: 1. Release the ZIF connector to which the TouchPad cable is connected, and then disconnect the TouchPad cable (1) from the TouchPad. 2. Disconnect the speaker cable (2) from the system board. 3. Remove the two rear rubber feet (1). Component replacement procedures 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
5.
Remove the solid-state drive connector board cable (see
Solid-state drive
on page
35
).
6.
Remove the Card Reader board cable (see
Card Reader board cable
on page
37
).
NOTE:
When replacing the top cover, be sure to remove the following components from the defective
top cover and install them on the replacement top cover:
●
NFC board (see
NFC board
on page
38
)
●
Solid-state drive connector board (see
Card Reader board cable
on page
37
)
●
Card Reader board (see
Card Reader board
on page
45
)
●
Power button board (see
Power button board
on page
46
)
Remove the top cover:
1.
Release the ZIF connector to which the TouchPad cable is connected, and then disconnect
the TouchPad cable
(1)
from the TouchPad.
2.
Disconnect the speaker cable
(2)
from the system board.
3.
Remove the two rear rubber feet
(1)
.
Component replacement procedures
41