HP Spectre Ultrabook 14-3200 HP Spectre Ultrabook PC Maintenance and Service G - Page 52

Solid-state drive connector board, Remove the Phillips PM2.0×3.6 screw

Get HP Spectre Ultrabook 14-3200 PDF manuals and user guides View all HP Spectre Ultrabook 14-3200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Reverse this procedure to install the top cover. Solid-state drive connector board Description Solid-state drive connector board (includes cable) Spare part number 675509-001 Before removing the solid-state drive connector board, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the battery (see Battery on page 33), and then remove the following components: a. Solid-state drive connector board cable (see Solid-state drive on page 35) b. Card Reader board cable (see Card Reader board cable on page 37) c. Top cover (see Top cover on page 40) Remove the solid-state drive connector board: 1. Turn the top cover upside down, with the front toward you. 2. Remove the Phillips PM2.0×3.6 screw (1) that secures the solid-state drive connector board to the top cover. 44 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Reverse this procedure to install the top cover.
Solid-state drive connector board
Description
Spare part number
Solid-state drive connector board (includes cable)
675509-001
Before removing the solid-state drive connector board, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see
Battery
on page
33
), and then remove the following components:
a.
Solid-state drive connector board cable (see
Solid-state drive
on page
35
)
b.
Card Reader board cable (see
Card Reader board cable
on page
37
)
c.
Top cover (see
Top cover
on page
40
)
Remove the solid-state drive connector board:
1.
Turn the top cover upside down, with the front toward you.
2.
Remove the Phillips PM2.0×3.6 screw
(1)
that secures the solid-state drive connector board to
the top cover.
44
Chapter 4
Removal and replacement procedures