HP Stream 11-aa000 Maintenance and Service Guide - Page 39

Hard drive, Release the zero insertion force ZIF connector

Get HP Stream 11-aa000 PDF manuals and user guides View all HP Stream 11-aa000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Hard drive NOTE: The hard drive spare part kit does not include the hard drive bracket, hard drive cable, or screws. The hard drive bracket, hard drive cable, and screws are included in the Hard Drive Hardware Kit, spare part number 906770-001. Description 500-GB, 5400-rpm, SATA, 7.0-mm hard drive Spare part number 778186-005 Before removing the hard drive, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the bottom cover (see Bottom cover on page 28). 5. Disconnect the battery cable from the system board (see Battery on page 30). Remove the hard drive: 1. Release the zero insertion force (ZIF) connector (1) to which the hard drive cable is connected, and then disconnect the hard drive cable from the system board. 2. Remove the four Phillips PM2.0×3.3 screws (2) that secure the hard drive to the keyboard/top cover. 3. Remove the hard drive (3). 4. If it is necessary to replace the hard drive cable, disconnect the cable (1) from the hard drive. Component replacement procedures 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
Hard drive
NOTE:
The hard drive spare part kit does not include the hard drive bracket, hard drive cable, or screws.
The hard drive bracket, hard drive cable, and screws are included in the Hard Drive Hardware Kit, spare part
number 906770-001.
Description
Spare part number
500-GB, 5400-rpm, SATA, 7.0-mm hard drive
778186-005
Before removing the hard drive, follow these steps:
1.
Turn
off
the computer. If you are unsure whether the computer is
off
or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
28
).
5.
Disconnect the battery cable from the system board (see
Battery
on page
30
).
Remove the hard drive:
1.
Release the zero insertion force (ZIF) connector
(1)
to which the hard drive cable is connected, and then
disconnect the hard drive cable from the system board.
2.
Remove the four Phillips PM2.0×3.3 screws
(2)
that secure the hard drive to the keyboard/top cover.
3.
Remove the hard drive
(3)
.
4.
If it is necessary to replace the hard drive cable, disconnect the cable
(1)
from the hard drive.
Component replacement procedures
31