HP Stream 13-c000 Maintenance and Service Guide - Page 64

Display assembly – touch screen models

Get HP Stream 13-c000 PDF manuals and user guides View all HP Stream 13-c000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Display assembly - touch screen models NOTE: The display assembly is spared at the subcomponent level only. For display assembly spare part information, see the individual removal subsections. Before removing the display assembly, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the keyboard/top cover (see Keyboard/top cover on page 29). 5. Disconnect the battery cable from the system board (see Battery on page 41). Remove the display assembly: 1. Disconnect the display cable from the system board (1). 2. Disconnect the WLAN and WWAN/GPS antenna cables (2) from the terminals on the WLAN and WWAN/GPS modules. 3. Release the display panel cable and the wireless antenna cables from the routing channels and clips (3) built into the bottom cover. 4. Remove the four Phillips PM2.5×4.5 screws (4) that secure the display assembly to the bottom cover. 5. Remove the display assembly (5). 6. If it is necessary to replace the display back cover or any of the display assembly internal components: a. Remove the display screw covers (1). 56 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
Display assembly – touch screen models
NOTE:
The display assembly is spared at the subcomponent level only. For display assembly spare part
information, see the individual removal subsections.
Before removing the display assembly, follow these steps:
1.
Turn
off
the computer. If you are unsure whether the computer is
off
or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the keyboard/top cover (see
Keyboard/top cover
on page
29
).
5.
Disconnect the battery cable from the system board (see
Battery
on page
41
).
Remove the display assembly:
1.
Disconnect the display cable from the system board
(1)
.
2.
Disconnect the WLAN and WWAN/GPS antenna cables
(2)
from the terminals on the WLAN and
WWAN/GPS modules.
3.
Release the display panel cable and the wireless antenna cables from the routing channels and clips
(3)
built into the bottom cover.
4.
Remove the four Phillips PM2.5×4.5 screws
(4)
that secure the display assembly to the bottom cover.
5.
Remove the display assembly
(5)
.
6.
If it is necessary to replace the display back cover or any of the display assembly internal components:
a.
Remove the display screw covers
(1)
.
56
Chapter 5
Removal and replacement procedures for Authorized Service Provider parts