HP j6700 hp workstation J6700 upgrade instructions (a6056-90000)
HP j6700 - Workstation Manual
View all HP j6700 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP j6700 manual content summary:
- HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 1
HP VISUALIZE J6700 UNIX® Workstations PA8700 Upgrade Instructions Manufacturing Part Number: A6056-90000 Edition E0501 © Copyright 2001 by Hewlett-Packard - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 2
consent of Hewlett-Packard Company. Hewlett-Packard Warranty Statement Refer to Warranty & Support for your HP Workstation for warranty terms applicable to your Hewlett-Packard product and replacement parts. Restricted Rights Legend Use, duplication, or disclosure by the U.S. Government Department - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 3
HP replacement part in your J6700 workstation does not affect the regulatory and safety classifications or approvals listed in the original owner's guide by following the instructions on the package. Attach the sticky end of the wrist strap to bare metal on the rear panel of the workstation. • Connect - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 4
contents: • System board upgrad tray assembly • Electrostatic Discharge (ESD) materials • Removal/Replacement Instructions If you are missing any part or any documentation, please call your designated service representative. Required Tools You will need the following tools for removal/replacement - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 5
to update HP-UX. 2. Determine the workstation's LAN ID by entering the following command: /usr/sbin/lanscan. The output is similar to the following: Hardware Station Crd Hardware Net-Interface NM MAC HP DLPI Mjr Path Address In# State NameUnit State ID Type Support Num 2.0.2 0x08000970ECC0 - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 6
Down the J6700 Workstation Safely Powering Down the J6700 Workstation You must complete the following steps before performing any of the removal and replacement procedures: CAUTION Do not use the power supply interlock thumbscrew on the rear panel to power down the workstation. This power down - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 7
Figure 1-1 shows an exploded view of the internal components (FRUs) in the J6700 workstations and Table 1-1 describes each of the exploded views components. Refer to this figure to identify the various workstation FRUs while performing the FRU removal and replacement procedures in Chapter 2. Figure - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 8
Diagram Table 1-1. Description of the Components in the J6700 Exploded Diagram Numbers in Figure 1-1 Description 1 J6700 System Board Assembly 2 Power supply 500W includes system speaker, power supply fans, and LCD display cable 3 SDRAM DIMMs 4 LVD Ultra SCSI hard disk 5 CD ROM slim - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 9
and replacing the components in the J6700 workstations. Chapter Overview Here are the main sections in this chapter: • Front Bezel and Top Panel • Bezel-Label Strip • LCD Panel • Hard Disk Drives • Hard disk Drive Backplane • CD ROM Drive • Memory DIMMs • Power Supply • PCI Cage • PCI Backplane - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 10
in each component or accessory removal and replacement procedures. Front Bezel and Top Cover This section describes how to remove and replace the J6700 workstation's front bezel and top cover. Note that you can perform certain operations, like removing and replacing hard disk drives, simply removing - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 11
Removal and Replacement Removing the Top Cover Figure 2-1. Removing the Top Cover 1 - Remove all connectors from back of workstation - Remove workstation from pedestal. 2 - Place workstation on a padded surface - Remove bezel - Press in on both sides of bezel and pull forward as shown. 1 2 Hold - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 12
Component Remove/Replacement Component Removal and Replacement Removing the Bezel-Label Strip If you have received the HP J6700 upgrade kit, you will need to remove the old bezel-label strip from your workstation and replace it with the new one. Here is the brief procedure for performing this task: - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 13
Removing the LCD Panel To remove the LCD panel, do the following: Figure 2-3. Removing the LCD Panel 1. Push LCD tab from one side to remove 2. Remove LCD 3. Remove connector Component Remove/Replacement Component Removal and Replacement 1 2 3 To replace the LCD panel, perform the above steps in - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 14
Component Remove/Replacement Component Removal and Replacement Removing the Hard Disk Drives To remove a hard disk drive do the following: Figure 2-4. Removing the Hard Disk Drives 1 1. Remove optional locking thumbscrew 2. Press HDD cover release tab to remove cover Locking Thumbscrew 1 2 Removing - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 15
, do the following: Figure 2-5. Removing the Hard Disk Drives Backplane 1 Remove PCI Cage - Lift PCI handle to remove PCI cage from workstation 2 - Remove disk drives BEFORE removing board. 3 - Unplug four connectors Press sides of connector to remove CD cable 1 4 - Remove four screws - Lift - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 16
2. Remove two screws 3. Slide CD to front 1 3 2 To replace the CD ROM drive, perform the above steps in reverse. Removing and Replacing Memory DIMMs To remove and replace memory DIMMs in the J6700, refer to the memory sequence label inside the system. Be sure to press the tabs at both ends of the - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 17
the power supply, do the following: Figure 2-7. Removing the Power Supply 1 - Remove two VRM connectors - Remove VRM 1 board as shown VRM 0 VRM connector Component Remove/Replacement Component Removal and Replacement VRM 1 VRM connector 2 - Remove screw from back of workstation to remove power - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 18
Component Remove/Replacement Component Removal and Replacement Figure 2-8. Removing the Power Supply (cont'd) 4 - Remove two screws from front of workstation - Push power supply to back of workstation to lift out. To replace the power supply, do the above steps in reverse. 18 Chapter 2 - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 19
PCI Cage To remove the PCI Cage, do the following: Figure 2-9. Removing the PCI Cage 1 - Lift PCI handle to remove cage from workstation 2 1. Slide PCI retainer back 2. Lift off cage PRCEITCAAINREDR 2 1 3 - Remove screw to remove card - Slide I/O card out as shown Bulkhead screw Chapter 2 19 - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 20
fan power plug 2. Remove mounting screw 1 Fan power plug 2 PCI mounting screw 2 - Slide board to back of cage and lift out To replace the PCI Backplane and Cage, do the above steps in reverse. Speaker The speaker is integrated into the power supply. If the speaker fails, replace the power supply - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 21
2 2. Remove memory cards from system board 1 3. Remove VRM connectors and VRM 0 and VRM 1 cards VRM 1 VRM 0 2 - Remove screw from back of workstation to remove power plug - Disconnect five connectors from system board (2-6) power plug 1 2 1 3 power plug screw 6 5 4 Chapter - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 22
the System Board 3 - Remove two mounting screws from system board. 4 - Remove four serial port screws from back of workstation. Mounting Screws Back serial port screws 5 - Pull system board toward front of workstation to remove from slots - Lift system board up Slots Front 22 Chapter 2 - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 23
Figure 2-13. Replacing the System Board - Reverse steps - Install PCI cage in workstation, with handle up, then press down. NOTE NOTE If you are replacing the system , go into the Boot Console Handler (BCH) and set the fan choice to desk side. Be sure to install the four serial port screws BEFORE - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 24
Component Remove/Replacement Component Removal and Replacement Removing and Replacing the Real-Time Clock To remove the real-time clock, you first need to follow the procedure in the section "Front Bezel and Top Cover" of this chapter. After this procedure has been completed, you can remove the real- - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 25
. In some cases you will need to use specific HP-UX commands and utilities to reconfigure the workstation to recognize the replacement part(s). Verifying System Operations To verify the system operation, follow these steps: 1. Reconnect the power cables and any other cables that were disconnected when - HP j6700 | hp workstation J6700 upgrade instructions (a6056-90000) - Page 26
Wrapping Up Verifying System Operations 26 Chapter 3
HP V
ISUALIZE
J6700 UNIX
®
Workstations
PA8700
Upgrade Instructions
Manufacturing Part Number: A6056-90000
Edition E0501
© Copyright 2001 by Hewlett-Packard