HP mt42 Maintenance and Service Guide - Page 39

SSD, Remove the SSD

Get HP mt42 PDF manuals and user guides View all HP mt42 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

SSD Description Solid-state drive, 2242.M2 128 GB 32 GB Spare part number 854106-001 827578-001 Before removing the SSD, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the bottom cover (see Bottom cover on page 25). 5. Disconnect the battery (see Battery on page 28). Remove the SSD: 1. Remove the Phillips PM2.0×3.0 screw (1) that secures the drive to the system board. 2. Remove the drive (2) by pulling it away from the connector. NOTE: SSD drives are designed with notches to prevent incorrect insertion. Reverse this procedure to reassemble and install the SSD drive. Component replacement procedures 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
SSD
Description
Spare part number
Solid-state drive
, 2242.M2
128 GB
854106-001
32 GB
827578-001
Before removing the SSD, follow these steps:
1.
Turn
off
the computer. If you are unsure whether the computer is
off
or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
25
).
5.
Disconnect the battery (see
Battery
on page
28
).
Remove the SSD:
1.
Remove the Phillips PM2.0×3.0 screw
(1)
that secures the drive to the system board.
2.
Remove the drive
(2)
by pulling it away from the connector.
NOTE:
SSD drives are designed with notches to prevent incorrect insertion.
Reverse this procedure to reassemble and install the SSD drive.
Component replacement procedures
29