Hitachi NT65MA2 Instruction Manual - Page 15

The Nailer Must Not Operate.

Get Hitachi NT65MA2 - Angled Finish Nailer PDF manuals and user guides
UPC - 717709007727
View all Hitachi NT65MA2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

English (4) Separate the push lever from the wood. Next, point the nailer downward, pull the trigger and then wait in that position for 5 seconds or longer. Ⅺ THE NAILER MUST NOT OPERATE. Pull Trigger (5) 1 Without touching the trigger, depress the push lever against the workpiece. Pull the trigger. Ⅺ THE NAILER MUST OPERATE. 2 Hold the trigger back while separating the push lever from the wood. Ⅺ The nailer will remain in operated status (the driver blade will remain at the bottom). 3 Remove the finger from the trigger. Ⅺ Nailer operation will end (the driver blade will return to the top). (6) Set the switching device to the downward position (CONTACT ACTUATION MECHANISM). (Set the switching device to the downward position completely as shown in the diagram. Otherwise, it will not operate properly.) Switching Device Downward position With the Nailer off the workpiece, pull the trigger. Depress the push lever against the workpiece. Ⅺ THE NAILER MUST OPERATE. (7) If no abnormal operation is observed, you may load nails in the Nailer. Drive nails into the workpiece that is the same type to be used in the actual application. Ⅺ THE NAILER MUST OPERATE PROPERLY. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
English
15
(4)
Separate the push lever from the wood.
Next, point the nailer downward, pull the trigger and then wait in that position for 5
seconds or longer.
²
THE NAILER MUST NOT OPERATE.
(5)
1
Without touching the trigger, depress the push lever against the workpiece.
Pull the trigger.
²
THE NAILER MUST OPERATE.
2
Hold the trigger back while separating the push lever from the wood.
²
The nailer will remain in operated status (the driver blade will remain at the bottom).
3
Remove the finger from the trigger.
²
Nailer operation will end (the driver blade will return to the top).
(6)
Set the switching device to the downward position (CONTACT ACTUATION
MECHANISM).
(Set the switching device to the downward position completely as shown in the diagram.
Otherwise, it will not operate properly.)
With the Nailer off the workpiece, pull the trigger.
Depress the push lever against the workpiece.
²
THE NAILER MUST OPERATE.
(7)
If no abnormal operation is observed, you may load nails in the Nailer.
Drive nails into the workpiece that is the same type to be used in the actual application.
²
THE NAILER MUST OPERATE PROPERLY.
Switching Device
Downward position
Pull Trigger