Hitachi NT65MA2 Instruction Manual - Page 21

Adjusting The Nailing Depth

Get Hitachi NT65MA2 - Angled Finish Nailer PDF manuals and user guides
UPC - 717709007727
View all Hitachi NT65MA2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

English You must first depress the push lever (upward position) where you wnat to drive a nail and then pull the trigger. After the each nail is driven, completely release the trigger and lift the tool off the work surface. An FULL SEQUENTIAL ACTUATION MECHANISM (SEQUENTIAL TRIP MECHANISM) may reduce the possibility of bodily injury to you or others in the work area. This is because it is less likely to drive an unwanted nail if you keep the trigger pulled and accidentally bump the push lever against yourself or others. An OPTIONAL SEQUENTIAL TRIP MECHANISM may also reduse the speed of operation compared to the standard contact trip mechanism. NOTE: ● If all warnings and instructions are followed, safe operation is possible with all three systems: SINGLE ACTUATION MECHANISM, CONTACT ACTUATION MECHANISM and FULL SEQUENTIAL ACTUATION MECHANISM. ● Always handle nails and package carefully. If nails are dropped, collating bond may be broken, which will cause mis-feeding and jamming. ● After nailing: 1) disconnect air hose from the Nailer; 2) remove all nails from the Nailer; 3) supply 5 - 10 drops of Hitachi pneumatic tool lubricant into the air plug on the Nailer; and 4) open the petcock on the air compressor tank to drain any moisture. ADJUSTING THE NAILING DEPTH WARNING ● When adjusting the Adjuster, be sure to remove your finger from the trigger and disconnect the air hose from the nailer. To assure that each nail penetrates to the same depth, be sure that: 1) the air pressure to the Nailer remains constant (requlator is installed and working properly), and 2) the Nailer is always held firmly against the workpiece. If nails are driven too deep or shallow into the workpiece, adjust the nailing in the following order. 1 DISCONNECT AIR HOSE FROM NAILER. 2 If nails are driven too deep, turn the adjuster to the shallow side. Adjustments are in half-turn increments. Adjuster 15 Disconnect air hose 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
English
21
You must first depress the push lever (upward position) where you wnat to drive a
nail and then pull the trigger. After the each nail is driven, completely release the
trigger and lift the tool off the work surface. An FULL SEQUENTIAL ACTUATION
MECHANISM (SEQUENTIAL TRIP MECHANISM) may reduce the possibility of bodily
injury to you or others in the work area. This is because it is less likely to drive an
unwanted nail if you keep the trigger pulled and accidentally bump the push lever
against yourself or others.
An OPTIONAL SEQUENTIAL TRIP MECHANISM may also reduse the speed of
operation compared to the standard contact trip mechanism.
NOTE:
●
If all warnings and instructions are followed, safe operation is possible with all three
systems: SINGLE ACTUATION MECHANISM, CONTACT ACTUATION MECHANISM and
FULL SEQUENTIAL ACTUATION MECHANISM.
●
Always handle nails and package carefully. If nails are dropped, collating bond may be
broken, which will cause mis-feeding and jamming.
●
After nailing:
1)
disconnect air hose from the Nailer;
2)
remove all nails from the Nailer;
3)
supply 5 – 10 drops of Hitachi pneumatic tool lubricant into the air plug on the Nailer;
and
4)
open the petcock on the air compressor tank to drain any moisture.
ADJUSTING THE NAILING DEPTH
WARNING
●
When adjusting the Adjuster, be sure to remove your finger from
the trigger and disconnect the air hose from the nailer.
To assure that each nail penetrates to the same
depth, be sure that:
1)
the air pressure to the Nailer remains constant
(requlator is installed and working properly),
and
2)
the Nailer is always held firmly against the
workpiece.
If nails are driven too deep or shallow into the
workpiece, adjust the nailing in the following order.
1
DISCONNECT AIR HOSE FROM NAILER.
2
If nails are driven too deep, turn the adjuster
to the shallow side.
Adjustments are in half-turn increments.
15
Disconnect
air hose
Adjuster