Hitachi NT65MA2 Instruction Manual - Page 19

Methods Of Operation

Get Hitachi NT65MA2 - Angled Finish Nailer PDF manuals and user guides
UPC - 717709007727
View all Hitachi NT65MA2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

English ⅜ CONTACT ACTUATION MECHANISM: First, press the push lever against the wood; next, pull the trigger to drive the nail. First, pull the trigger; next, press the push lever against the wood to drive the nail. If the trigger is held back, a nail will be driven each time the push lever is pressed against the wood. ⅜ FULL SEQUENTIAL ACTUATION MECHANISM: First, press the push lever against the wood; next, pull the trigger to drive the nail. Follow the same sequence to continue driving nails. METHODS OF OPERATION This Nailer is equipped with the push lever and does not operate unless the push lever is depressed (upward position). There are two methods of operation to drive nails with this Nailer. They are: 1. Intermittent operation (Trigger fire): 2. Continuous operation (Push lever fire): (1) Intermittent operation (Trigger fire) Use the SINGLE ACTUATION MECHANISM setting. WARNING ● Unlike the FULL SEQUENTIAL ACTUATION MECHANISM, please note that the SINGLE ACTUATION MECHANISM of this Hitachi nailer will drive a nail each time the push lever is pressed against the wood as long as the trigger is pressed. ● For intermittent operation, set the switching device to the upward position completely. (i.e. Set to SINGLE ACTUATION MECHANISM.) ● To avoid double firing or accidental firing due to recoil. 1) Set the switching device to SINGLE ACTUATION MECHANISM. 2) Pull the trigger rapidly and firmly. 1 Set the switching device to the upward position (to set to SINGLE ACTUATION MECHANISM). (Set the switching device to the upward position completely as shown in the diagram. Otherwise, it will be set to CONTACT ACTUATION MECHANISM.) 2 Position the nail outlet on the workpiece with finger off the trigger. 3 Depress the push lever firmly until it is completely depressed. 4 Pull the trigger to drive a nail. 5 Remove finger from the trigger. To continue nailing in a separate location, move the nailer along the wood, repeating steps 2 - 5 as required. Push Lever 3 1 Upward position 4 Switching Device Trigger 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
English
19
±
CONTACT ACTUATION MECHANISM: First, press the push lever against the wood;
next, pull the trigger to drive the nail.
First, pull the trigger; next, press the push lever against the wood to drive the nail.
If the trigger is held back, a nail will be driven each time the push lever is pressed
against the wood.
±
FULL SEQUENTIAL ACTUATION MECHANISM: First, press the push lever against the
wood; next, pull the trigger to drive the nail. Follow the same sequence to continue
driving nails.
METHODS OF OPERATION
This Nailer is equipped with the push lever and does not operate unless the push lever is
depressed (upward position).
There are two methods of operation to drive nails with this Nailer.
They are:
1.
Intermittent operation (Trigger fire):
2.
Continuous operation (Push lever fire):
(1)
Intermittent operation (Trigger fire)
Use the SINGLE ACTUATION MECHANISM setting.
WARNING
●
Unlike the FULL SEQUENTIAL ACTUATION MECHANISM, please
note that the SINGLE ACTUATION MECHANISM of this Hitachi
nailer will drive a nail each time the push lever is pressed against
the wood as long as the trigger is pressed.
●
For intermittent operation, set the switching device to the upward
position completely. (i.e. Set to SINGLE ACTUATION
MECHANISM.)
●
To avoid double firing or accidental firing due to recoil.
1)
Set the switching device to SINGLE ACTUATION MECHANISM.
2)
Pull the trigger rapidly and firmly.
1
Set the switching device to the upward position (to set to SINGLE ACTUATION
MECHANISM).
(Set the switching device to the upward position completely as shown in the
diagram. Otherwise, it will be set to CONTACT ACTUATION MECHANISM.)
2
Position the nail outlet on the workpiece with finger off the trigger.
3
Depress the push lever firmly until it is completely depressed.
4
Pull the trigger to drive a nail.
5
Remove finger from the trigger.
To continue nailing in a separate location, move the nailer along the wood, repeating
steps
2
-
5
as required.
Push Lever
Trigger
Switching Device
1
Upward position
3
4