Hitachi VB16Y Instruction Manual - Page 12

Assembly And Operation - rebar cutter

Get Hitachi VB16Y - Rebar Cutter And Bender PDF manuals and user guides
UPC - 717709006256
View all Hitachi VB16Y manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

English ASSEMBLY AND OPERATION APPLICATIONS ⅜ Cutting of rebar ⅜ Bending of rebar PRIOR TO OPERATION 1. Power source Ensure that the power source to be utilized conforms to the power source requirements specified on the product nameplate. Also, avoid using DC power or engine generators. Not only will the tool get damaged but an accident can result. 2. Power switch Ensure that the switch is in the OFF position. If the plug is connected to a receptacle while the switch is in the ON position, the power tool will start operating immediately and can cause serious injury. 3. Extension cord When the work area is far away from the power source, use an extension cord of sufficient thickness and rated capacity. The extension cord should be kept as short as practicable. WARNING: Damaged cord must be replaced or repaired. 4. Check the receptacle If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact a licensed electrician to make appropriate repairs. If such a fautly receptacle is used, it may cause overheating, resulting in a serious hazard. 5. Confirming condition of the environment Confirm that the work site is placed under appropriate conditions conforming to prescribed precautions. 6. For safety sake, use the provided Allen key to make absolutely sure that the hexagon socket bolt is securely clamped. Use of the unit with the bolt in a loosely clamped condition can result in damage to the unit and cutter as well as accidents. 7. Confirm that the cutter is in sharp condition. Make certain that the cutter is in a sharp condition. Continued use of a worn out and deformed cutter with dull edges results in damage to the unit and cutter as well as accidents. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
English
12
ASSEMBLY AND OPERATION
APPLICATIONS
±
Cutting of rebar
±
Bending of rebar
PRIOR TO OPERATION
1.
Power source
Ensure that the power source to be utilized conforms to the power source requirements
specified on the product nameplate.
Also, avoid using DC power or engine generators. Not only will the tool get damaged
but an accident can result.
2.
Power switch
Ensure that the switch is in the OFF position. If the plug is connected to a receptacle
while the switch is in the ON position, the power tool will start operating immediately
and can cause serious injury.
3.
Extension cord
When the work area is far away from the power source, use an extension cord of
sufficient thickness and rated capacity. The extension cord should be kept as short as
practicable.
WARNING:
Damaged cord must be replaced or repaired.
4.
Check the receptacle
If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact
a licensed electrician to make appropriate repairs.
If such a fautly receptacle is used, it may cause overheating, resulting in a serious
hazard.
5.
Confirming condition of the environment
Confirm that the work site is placed under appropriate conditions conforming to
prescribed precautions.
6.
For safety sake, use the provided Allen key to make absolutely sure that the hexagon
socket bolt is securely clamped. Use of the unit with the bolt in a loosely clamped
condition can result in damage to the unit and cutter as well as accidents.
7.
Confirm that the cutter is in sharp condition.
Make certain that the cutter is in a sharp condition. Continued use of a worn out and
deformed cutter with dull edges results in damage to the unit and cutter as well as
accidents.