Honeywell TB7100A1000 Installation Instructions - Page 10
Table 4. Installer Setup Menu. Continued, Installer, Setup, Number, Installer Setup, Default, - manual
View all Honeywell TB7100A1000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT Table 4. Installer Setup Menu. (Continued) Installer Setup Number Installer Setup Name Default Setting All Settings Notes 0300 Changeover 1 0-Manual 1-Auto Only shown if system has both heat and cool stages (ISU 0170). Shown for CNV, HP, PTAC and 4 pipe fan coil (ISU 0170). Not shown for 2 pipe fan coil modes. 0310 Deadband 3°F (2°C) 2 (1.5)-2°F (1.5°C) 3 (2.0)-3°F (2.0°C) 4 (2.5)-4°F (2.5°C) 5 (3.0)-5°F (3.0°C) 6 (3.5)-6°F (3.5°C) 7 (4.0)-7°F (4.0°C) 8 (4.5)-8°F (4.5°C) 9 (5.0)-9°F (5.0°C) Only shown if Automatic Changeover selected (ISU 0300). 0320 Temperature 0 Indication Scale 0-°F 1-°C 0330 Daylight Saving 1 0-Disabled 1-Enabled (US) 0340 Remote Temp 0 Sensor/Remote Setback/ Changeover Input 0-None 1-Remote 10K Indoor 2-Remote 20K Indoor 3-Changeover 2 pipe Fan Coil modes only 4-Changeover 2 pipe Fan Coil modes only Only shown on models that offer remote sensing. NO input (default mode is Heat) NO input (default mode is Cool) 0340 Remote Temp 0 (Non- Sensor/Remote program Setback/ mable) Changeover Input 0-None 1-Remote 10K Indoor 2-Remote 20K Indoor 3-Changeover 2 pipe Fan Coil modes only 4-Changeover 2 pipe Fan Coil modes only 5-Remote Setback 6-Remote Setback Only shown on models that offer remote sensing. NO input (default mode is Heat) NO input (default mode is Cool) Hotel card NO, with 1 second software delay going from UnOcc to Occupied; 2 minute delay going from Occupied to UnOcc. Hotel Card NC, with 1 second software delay going from UnOcc to Occupied; 2 minute delay going from Occupied to UnOcc. 0341 Delay for Remote 0 Setback 0-No Delay 2-2 Minute Delay Only shown if Remote Setback (ISU 0340) is enabled. 0342 Override Option 0 (only available in non-programmable mode) 0-No Override 1-Override This option is only available for non-programmable mode (ISU 0160) 0343 Unoccupied Heating Setpoint (only when remote setback enabled) 60°F 50-65°F 10-18°C 0346 Unoccupied 80°F Cooling Setpoint (only when remote setback is enabled) 75-90°F 24-30°C 0347 Fan Ramping 1 0-Disabled (Lo, Med, Hi) To enable the fan ramping algorithm. Only 1-Enabled available for fan coil or PTAC applications. 0348 Fan Mode 0 0-User can choose To select a particular fan mode: Auto is the fan Cycle or Constant 3 ramp mode. If ramping is not selected, fan mode speed: Low->Med-> automatically defaults to Low Med High (Constant High->Auto-> Low only) and ISU 0348 is unavailable. Only available 1-Cycle Only - Auto only for fan coil or PTAC applications. 62-0273-05 10