Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 450XH » Manual Viewer

Husqvarna AUTOMOWER 450XH Owner Manual - Page 27

> Lawn Coverage

View all Husqvarna AUTOMOWER 450XH manuals

Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Any grass twisted around the blade disc shaft, or blunt blades, can affect the Weather timer. Note: If the mowing results are not satisfying, the cutting time can be adjusted to mow for a longer time (High) or for a shorter time (Low). 3.10.6.1 To set the Weather timer 1. Do steps 1-3 in To get access to the menu on page 24. 2. Use the arrow buttons and the OK button to move through the menu structure Weather timer > Use. 3. Push the OK button to select Weather timer. 4. Use the arrow buttons to set the cutting time. You can select between Low, Mid, High. 3.10.7 Installation In the Installation menu it is possible to adapt the settings of the product for best mowing result. 3.10.7.1 Lawn coverage GPS Assisted Navigation helps the product to select the most optimal operation. Refer to To disable and enable the GPS function on page 27. In more complex gardens operation can be improved by carrying out some of the manual settings in the Lawn coverage menu. The Lawn coverage function is used to guide the product to remote parts of the work area. If the work area includes areas that are connected with narrow passages, the Lawn coverage function is useful to be able to maintain a well-cut lawn in all parts of the yard. The product begins to mow when it reaches the Lawn coverage point. At all other times, the product leaves the charging station in the standard manner and starts to mow. To disable and enable the GPS function Disable the GPS Assisted Navigation to make manual settings in Lawn Coverage. Note: It is recommended to use GPS Assisted Navigation. 1. Do steps 1-3 in To get access to the menu on page 24. 2. Use the arrow buttons and the OK button to move through the menu structure Installation > Lawn Coverage. 3. Push the OK button to disable or enable the GPS Assisted Navigation. Note: When GPS assisted navigation is enabled it is used as long as there is a GPS service. The GPS assisted navigation is used even if manual settings have been made. Only when GPS service is not available, the manual settings are used. To set the Lawn coverage function 1. Do steps 1-3 in To get access to the menu on page 24. 2. Use the arrow buttons and the OK button to move through the menu structure Installation > Lawn coverage > Area 1-5. 3. Use the left arrow button to select the area. 4. Push the OK button. 5. Measure the distance from the charging station to the start of the area. Measure along the guide wire. Refer to To measure 1230 - 001 - Installation - 27

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
Menu structure overview 1	7
Menu structure overview 2	8
Menu structure overview 3	9
Display	10
Keypad	10
Safety	11
Safety definitions	11
General safety instructions	11
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	12
Safety instructions for operation	13
Use	13
Battery safety	14
How to lift and move the product	14
Maintenance	15
In the event of a thunderstorm	15
Installation	16
Introduction - Installation	16
Before the installation of the wires	16
Before the installation of the product	16
To examine where to put the charging station	16
To examine where to put the power supply	17
To examine where to put the boundary wire	17
To put the boundary wire in a slope	18
Passages	18
To make an island	18
To make a secondary area	19
To examine where to put the guide wire	19
Work area examples	20
Installation of the product	20
To install the charging station	20
To install the boundary wire	21
To install the guide wire	21
To put the wire into position with stakes	22
To bury the boundary wire or the guide wire	22
To extend the boundary wire or the guide wire	22
After the installation of the product	22
To do a visual check of the charging station	22
To do the basic settings	23
Automower® Connect app	23
To install the Automower® Connect app	23
Automower® Connect menu	23
Dashboard	23
Map	24
Settings in Automower® Connect	24
To do the product settings	24
To get access to the menu	24
To do the timer settings	24
To calculate the timer setting	24
To set the timer	24
To copy the timer setting	24
To reset the timer setting	25
Cutting height	25
To set the cutting height	25
Security level	25
To set the security level	25
To change the PIN-code	26
To create a New loop signal	26
To set duration of alarm and time lock	26
Messages	26
To read the messages	26
Weather timer	26
To set the Weather timer	27
Installation	27
Lawn coverage	27
To disable and enable the GPS function	27
To set the Lawn coverage function	27
To do a test of the Lawn coverage function	28
To measure the distance from the charging station	28
To disable or enable the Lawn coverage function	28
Finding the charging station	28
To set the delay time for the guide wire and the boundary wire	29
To disable the guide wire and boundary wire	29
To test if the product can find the charging station	29
To reset the settings for the guide wire and the boundary wire	29
To change the signal range of the charging station	29
Advanced	29
Corridor width	29
To set the corridor width	29
Exit angles	30
To set the exit angles	30
To set the reversing distance	30
To set the Drive Past Wire function	30
Settings	30
Profiles	30
To save settings to a profile	30
To use a profile	31
ECO mode	31
To set the ECO mode	31
Spiral Cutting	31
To set the level of Spiral Cutting	31
Slope Control	31
To enable or disable the Slope control	31
General	31
To set the time & date	31
To set the language	32
To set the Country & Timezone	32
To reset all user settings	32
The About menu	32
Accessories	32
Information	32
Automower® Connect	32
To pair Automower® Connect and the product	32
To set the Geofence level of sensitivity	32
To use the SMS function	32
Network	33
SIM PIN	33
APN settings	33
To reset the Automower® Connect settings	33
Headlights	33
To set the schedule for the headlights	33
To set the Flashes when fault function	33
Ultrasonic (Automower® 450XH)	33
To set the Ultrasonic function	33
Mower house	33
To avoid collisions with the mower house	33
Operation	34
Main switch	34
To start the product	34
Operating mode - Start	34
Main area	34
Override timer	34
Secondary area	34
Spot cutting	35
Operating mode - Park	35
Park until further notice	35
Start again in 3 hours	35
Start with next timer	35
To stop the product	35
To switch off the product	35
To charge the battery	35
Maintenance	37
Introduction - maintenance	37
Clean the product	37
Chassis and blade disc	37
Chassis	37
Wheels	37
Cover	37
Charging station	37
Replace the blades	38
To replace the blades	38
Battery	38
Winter service	39
Troubleshooting	40
Introduction - troubleshooting	40
Fault messages	40
Information messages	45
LED indicator lamp on the charging station	47
LED indicator lamp on the product	48
Symptoms	49
Finding breaks in the loop wire	50
Transportation, storage and disposal	53
Transportation	53
Storage	53
Disposal	53
To remove the battery	53
Technical data	54
Technical data	54
Warranty	57
Warranty terms	57
Applicable to US/CA market	58
Supplier's Declaration of Conformity	58

Match case Limit results 1 per page

Any grass twisted around the blade disc shaft, or

blunt blades, can affect the

Weather timer

Note:

If the mowing results are not satisfying, the

cutting time can be adjusted to mow for a longer

time

(High)

or for a shorter time

(Low)

3.10.6.1 To set the Weather timer

Do steps 1–3 in

To get access to the menu

on page 24

Use the

arrow

buttons and the

button to

move through the menu structure

Weather

timer > Use

Push the

button to select

Weather timer

Use the

arrow

buttons to set the cutting

time. You can select between

Low, Mid,

High

3.10.7 Installation

In the Installation menu it is possible to

adapt the settings of the product for

best mowing result.

3.10.7.1 Lawn coverage

GPS Assisted Navigation helps the product to

select the most optimal operation. Refer to

disable and enable the GPS function on page

. In more complex gardens operation can be

improved by carrying out some of the manual

settings in the

Lawn coverage

menu.

The

Lawn coverage

function is used to guide the

product to remote parts of the work area. If the

work area includes areas that are connected with

narrow passages, the

Lawn coverage

function is

useful to be able to maintain a well-cut lawn in all

parts of the yard. The product begins to mow

when it reaches the

Lawn coverage

point. At all

other times, the product leaves the charging

station in the standard manner and starts to mow.

To disable and enable the GPS function

Disable the GPS Assisted Navigation to make

manual settings in

Lawn Coverage

Note:

It is recommended to use GPS Assisted

Navigation.

Do steps 1–3 in

To get access to the menu

on page 24

Use the

arrow

buttons and the

button to

move through the menu structure

Installation

> Lawn Coverage

Push the

button to disable or enable the

GPS Assisted Navigation.

Note:

When GPS assisted navigation is enabled

it is used as long as there is a GPS service. The

GPS assisted navigation is used even if manual

settings have been made. Only when GPS

service is not available, the manual settings are

used.

To set the Lawn coverage function

Do steps 1–3 in

To get access to the menu

on page 24

Use the

arrow

buttons and the

button to

move through the menu structure

Installation

> Lawn coverage > Area 1-5

Use the left

arrow

button to select the area.

Push the

button.

Measure the distance from the charging

station to the start of the area. Measure

along the guide wire. Refer to

To measure

1230 - 001 -

Installation -