Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 450XH » Manual Viewer

Husqvarna AUTOMOWER 450XH Owner Manual - Page 34

Main switch, 2 To start the product, 3 Operating mode - Start

View all Husqvarna AUTOMOWER 450XH manuals

Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

4 Operation 4.1 Main switch WARNING: Read the safety instructions carefully before you start the product. WARNING: Keep your hands and feet away from the rotating blades. Never put your hands or feet close to or under the product when the motor is running. WARNING: Do not use the product when persons, especially children, or animals, are in the work area. 5. Select the desired operating mode. Refer to Operating mode - Start on page 34. 6. Close the hatch within 10 seconds. If the product is parked in the charging station, it will only leave the charging station when the battery is fully charged and if the timer is set to allow the product to operate. Note: Always press the START button before closing the hatch to start the product. • Set the Main switch in the 1 position to start the product. • Set the Main switch in the 0 position when the product is not in use or before any work, inspection or maintenance is being carried out. When the Main switch is set in the 0 position the motors on the product cannot start. 4.2 To start the product 1. Press the STOP button to open the hatch. 2. Set the main switch to position 1. 3. Enter the PIN code. 4. Press the START button. 4.3 Operating mode - Start When the START button has been pushed the following operation selections can be selected. • Main area • Secondary area • Override timer • Spot cutting 4.3.1 Main area Main area is the standard operating mode where the product mows and charges automatically. 4.3.2 Override timer The timer settings can be temporarily overridden by selecting Override timer. It is possible to override the timer for 24 h or 3 days. 4.3.3 Secondary area In the Secondary area mode, the product operates until the battery is empty. When the battery is empty, the product stops and the message Needs manual charging shows in the product display. Put the product in the charging station to charge the battery. 34 - Operation 1230 - 001 -

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
Menu structure overview 1	7
Menu structure overview 2	8
Menu structure overview 3	9
Display	10
Keypad	10
Safety	11
Safety definitions	11
General safety instructions	11
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	12
Safety instructions for operation	13
Use	13
Battery safety	14
How to lift and move the product	14
Maintenance	15
In the event of a thunderstorm	15
Installation	16
Introduction - Installation	16
Before the installation of the wires	16
Before the installation of the product	16
To examine where to put the charging station	16
To examine where to put the power supply	17
To examine where to put the boundary wire	17
To put the boundary wire in a slope	18
Passages	18
To make an island	18
To make a secondary area	19
To examine where to put the guide wire	19
Work area examples	20
Installation of the product	20
To install the charging station	20
To install the boundary wire	21
To install the guide wire	21
To put the wire into position with stakes	22
To bury the boundary wire or the guide wire	22
To extend the boundary wire or the guide wire	22
After the installation of the product	22
To do a visual check of the charging station	22
To do the basic settings	23
Automower® Connect app	23
To install the Automower® Connect app	23
Automower® Connect menu	23
Dashboard	23
Map	24
Settings in Automower® Connect	24
To do the product settings	24
To get access to the menu	24
To do the timer settings	24
To calculate the timer setting	24
To set the timer	24
To copy the timer setting	24
To reset the timer setting	25
Cutting height	25
To set the cutting height	25
Security level	25
To set the security level	25
To change the PIN-code	26
To create a New loop signal	26
To set duration of alarm and time lock	26
Messages	26
To read the messages	26
Weather timer	26
To set the Weather timer	27
Installation	27
Lawn coverage	27
To disable and enable the GPS function	27
To set the Lawn coverage function	27
To do a test of the Lawn coverage function	28
To measure the distance from the charging station	28
To disable or enable the Lawn coverage function	28
Finding the charging station	28
To set the delay time for the guide wire and the boundary wire	29
To disable the guide wire and boundary wire	29
To test if the product can find the charging station	29
To reset the settings for the guide wire and the boundary wire	29
To change the signal range of the charging station	29
Advanced	29
Corridor width	29
To set the corridor width	29
Exit angles	30
To set the exit angles	30
To set the reversing distance	30
To set the Drive Past Wire function	30
Settings	30
Profiles	30
To save settings to a profile	30
To use a profile	31
ECO mode	31
To set the ECO mode	31
Spiral Cutting	31
To set the level of Spiral Cutting	31
Slope Control	31
To enable or disable the Slope control	31
General	31
To set the time & date	31
To set the language	32
To set the Country & Timezone	32
To reset all user settings	32
The About menu	32
Accessories	32
Information	32
Automower® Connect	32
To pair Automower® Connect and the product	32
To set the Geofence level of sensitivity	32
To use the SMS function	32
Network	33
SIM PIN	33
APN settings	33
To reset the Automower® Connect settings	33
Headlights	33
To set the schedule for the headlights	33
To set the Flashes when fault function	33
Ultrasonic (Automower® 450XH)	33
To set the Ultrasonic function	33
Mower house	33
To avoid collisions with the mower house	33
Operation	34
Main switch	34
To start the product	34
Operating mode - Start	34
Main area	34
Override timer	34
Secondary area	34
Spot cutting	35
Operating mode - Park	35
Park until further notice	35
Start again in 3 hours	35
Start with next timer	35
To stop the product	35
To switch off the product	35
To charge the battery	35
Maintenance	37
Introduction - maintenance	37
Clean the product	37
Chassis and blade disc	37
Chassis	37
Wheels	37
Cover	37
Charging station	37
Replace the blades	38
To replace the blades	38
Battery	38
Winter service	39
Troubleshooting	40
Introduction - troubleshooting	40
Fault messages	40
Information messages	45
LED indicator lamp on the charging station	47
LED indicator lamp on the product	48
Symptoms	49
Finding breaks in the loop wire	50
Transportation, storage and disposal	53
Transportation	53
Storage	53
Disposal	53
To remove the battery	53
Technical data	54
Technical data	54
Warranty	57
Warranty terms	57
Applicable to US/CA market	58
Supplier's Declaration of Conformity	58

Match case Limit results 1 per page

4 Operation

4.1 Main switch

WARNING:

Read the safety

instructions carefully before you start

the product.

WARNING:

Keep your hands and feet

away from the rotating blades. Never

put your hands or feet close to or

under the product when the motor is

running.

WARNING:

Do not use the product

when persons, especially children, or

animals, are in the work area.

•

Set the

Main switch

in the

position to start

the product.

•

Set the

Main switch

in the

position when

the product is not in use or before any work,

inspection or maintenance is being carried

out.

When the

Main switch

is set in the

position

the motors on the product cannot start.

4.2 To start the product

Press the

STOP

button to open the hatch.

Set the main switch to position

Enter the PIN code.

Press the

START

button.

Select the desired operating mode. Refer to

Operating mode - Start on page 34

Close the hatch within 10 seconds.

If the product is parked in the charging

station, it will only leave the charging station

when the battery is fully charged and if the

timer is set to allow the product to operate.

Note:

Always press the

START

button before

closing the hatch to start the product.

4.3 Operating mode - Start

When the

START

button has been pushed the

following operation selections can be selected.

•

Main area

•

Secondary area

•

Override timer

•

Spot cutting

4.3.1 Main area

Main area

is the standard operating mode where

the product mows and charges automatically.

4.3.2 Override timer

The timer settings can be temporarily overridden

by selecting

Override timer

. It is possible to

override the timer for 24 h or 3 days.

4.3.3 Secondary area

In the

Secondary area

mode, the product

operates until the battery is empty.

When the battery is empty, the product stops and

the message

Needs manual charging

shows in

the product display. Put the product in the

charging station to charge the battery.

- Operation

1230 - 001 -