Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 450XH » Manual Viewer

Husqvarna AUTOMOWER 450XH Owner Manual - Page 47

LED indicator lamp on the charging station

View all Husqvarna AUTOMOWER 450XH manuals

Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Message Weak signal Cause Weak GPS signal for Automower® Connect module Action Make sure that the product is not upside down. If the problem remains, the message requires action by an authorized service technician. SIM card requires The SIM card must be unlocked. PIN Make sure the correct SIM PIN has been entered into the mower's menu (Network > SIM card). Contact your local Husqvarna representative if this message appears often. SIM card locked The SIM card must be replaced. Contact your local Husqvarna representative. SIM card not found Automower® Connect requires a SIM Contact your local Husqvarna repre- card to be inserted in the mower. sentative. GeoFence prob- The GeoFence is not work due to poor Contact your local Husqvarna repre- lem (or no) communication with the system. sentative. 6.4 LED indicator lamp on the charging station For a fully functional installation, the indicator lamp in the charging station must emit a solid or flashing green light. If any other color than green is visible, follow the troubleshooting guide below. There is more help on www.husqvarna.com. If you still need help, please contact your local Husqvarna representative. Light Green solid light Green flashing light Blue flashing light Cause Action Good signals No action required The signals are good and ECO mode is No action required. For more informa- activated. tion on ECO mode. Refer to ECO mode on page 31. The boundary loop is not connected to the charging station. Check that the boundary wire connectors are fitted properly to the charging station. Refer to To install the boundary wire on page 21. Red flashing light Red solid light Break in the boundary loop. Find out where the break is. Replace the damaged section of the loop with a new loop wire and splice using an original coupler. Interruption in the charging station's an- Contact your local Husqvarna repre- tenna. sentative. Fault in the circuit board or incorrect power supply in the charging station. The fault should be rectified by an authorized service technician. Contact your local Husqvarna representative. 1230 - 001 - Troubleshooting - 47

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
Menu structure overview 1	7
Menu structure overview 2	8
Menu structure overview 3	9
Display	10
Keypad	10
Safety	11
Safety definitions	11
General safety instructions	11
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	12
Safety instructions for operation	13
Use	13
Battery safety	14
How to lift and move the product	14
Maintenance	15
In the event of a thunderstorm	15
Installation	16
Introduction - Installation	16
Before the installation of the wires	16
Before the installation of the product	16
To examine where to put the charging station	16
To examine where to put the power supply	17
To examine where to put the boundary wire	17
To put the boundary wire in a slope	18
Passages	18
To make an island	18
To make a secondary area	19
To examine where to put the guide wire	19
Work area examples	20
Installation of the product	20
To install the charging station	20
To install the boundary wire	21
To install the guide wire	21
To put the wire into position with stakes	22
To bury the boundary wire or the guide wire	22
To extend the boundary wire or the guide wire	22
After the installation of the product	22
To do a visual check of the charging station	22
To do the basic settings	23
Automower® Connect app	23
To install the Automower® Connect app	23
Automower® Connect menu	23
Dashboard	23
Map	24
Settings in Automower® Connect	24
To do the product settings	24
To get access to the menu	24
To do the timer settings	24
To calculate the timer setting	24
To set the timer	24
To copy the timer setting	24
To reset the timer setting	25
Cutting height	25
To set the cutting height	25
Security level	25
To set the security level	25
To change the PIN-code	26
To create a New loop signal	26
To set duration of alarm and time lock	26
Messages	26
To read the messages	26
Weather timer	26
To set the Weather timer	27
Installation	27
Lawn coverage	27
To disable and enable the GPS function	27
To set the Lawn coverage function	27
To do a test of the Lawn coverage function	28
To measure the distance from the charging station	28
To disable or enable the Lawn coverage function	28
Finding the charging station	28
To set the delay time for the guide wire and the boundary wire	29
To disable the guide wire and boundary wire	29
To test if the product can find the charging station	29
To reset the settings for the guide wire and the boundary wire	29
To change the signal range of the charging station	29
Advanced	29
Corridor width	29
To set the corridor width	29
Exit angles	30
To set the exit angles	30
To set the reversing distance	30
To set the Drive Past Wire function	30
Settings	30
Profiles	30
To save settings to a profile	30
To use a profile	31
ECO mode	31
To set the ECO mode	31
Spiral Cutting	31
To set the level of Spiral Cutting	31
Slope Control	31
To enable or disable the Slope control	31
General	31
To set the time & date	31
To set the language	32
To set the Country & Timezone	32
To reset all user settings	32
The About menu	32
Accessories	32
Information	32
Automower® Connect	32
To pair Automower® Connect and the product	32
To set the Geofence level of sensitivity	32
To use the SMS function	32
Network	33
SIM PIN	33
APN settings	33
To reset the Automower® Connect settings	33
Headlights	33
To set the schedule for the headlights	33
To set the Flashes when fault function	33
Ultrasonic (Automower® 450XH)	33
To set the Ultrasonic function	33
Mower house	33
To avoid collisions with the mower house	33
Operation	34
Main switch	34
To start the product	34
Operating mode - Start	34
Main area	34
Override timer	34
Secondary area	34
Spot cutting	35
Operating mode - Park	35
Park until further notice	35
Start again in 3 hours	35
Start with next timer	35
To stop the product	35
To switch off the product	35
To charge the battery	35
Maintenance	37
Introduction - maintenance	37
Clean the product	37
Chassis and blade disc	37
Chassis	37
Wheels	37
Cover	37
Charging station	37
Replace the blades	38
To replace the blades	38
Battery	38
Winter service	39
Troubleshooting	40
Introduction - troubleshooting	40
Fault messages	40
Information messages	45
LED indicator lamp on the charging station	47
LED indicator lamp on the product	48
Symptoms	49
Finding breaks in the loop wire	50
Transportation, storage and disposal	53
Transportation	53
Storage	53
Disposal	53
To remove the battery	53
Technical data	54
Technical data	54
Warranty	57
Warranty terms	57
Applicable to US/CA market	58
Supplier's Declaration of Conformity	58

Match case Limit results 1 per page

Message

Cause

Action

Weak signal

Weak GPS signal for Automower

Connect module

Make sure that the product is not up-

side down. If the problem remains, the

message requires action by an author-

ized service technician.

SIM card requires

The SIM card must be unlocked.

Make sure the correct SIM PIN has

been entered into the mower's menu

(Network > SIM card). Contact your lo-

cal Husqvarna representative if this

message appears often.

SIM card locked

The SIM card must be replaced.

Contact your local Husqvarna repre-

sentative.

SIM card not found

Automower

Connect requires a SIM

card to be inserted in the mower.

Contact your local Husqvarna repre-

sentative.

GeoFence prob-

lem

The GeoFence is not work due to poor

(or no) communication with the system.

Contact your local Husqvarna repre-

sentative.

6.4 LED indicator lamp on the charging station

For a fully functional installation, the indicator lamp in the charging station must emit a solid or flashing

green light. If any other color than green is visible, follow the troubleshooting guide below.

There is more help on www.husqvarna.com. If you still need help, please contact your local Husqvarna

representative.

Light

Cause

Action

Green solid light

Good signals

No action required

Green flashing

light

The signals are good and

ECO mode

activated.

No action required. For more informa-

tion on

ECO mode

. Refer to

ECO mode

on page 31

Blue flashing light

The boundary loop is not connected to

the charging station.

Check that the boundary wire connec-

tors are fitted properly to the charging

station. Refer to

To install the boundary

wire on page 21

Break in the boundary loop.

Find out where the break is. Replace

the damaged section of the loop with a

new loop wire and splice using an origi-

nal coupler.

Red flashing light

Interruption in the charging station’s an-

tenna.

Contact your local Husqvarna repre-

sentative.

Red solid light

Fault in the circuit board or incorrect

power supply in the charging station.

The fault should be rectified by an au-

thorized service technician.

Contact your local Husqvarna repre-

sentative.

1230 - 001 -

Troubleshooting -