Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 450XH » Manual Viewer

Husqvarna AUTOMOWER 450XH Owner Manual - Page 42

Message, Cause, Action

View all Husqvarna AUTOMOWER 450XH manuals

Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Message Cause Action Outside work area The boundary wire connections to the Check that the boundary wire is con- charging station are crossed. nected correctly. The boundary wire is too close to the edge of the work area. The work area slopes too much by the boundary loop. Check that the boundary wire has been laid according to the instructions. Refer to To install the boundary wire on page 21. The boundary wire is laid in the wrong direction around an island. Disturbances from metal objects (fences, reinforcement steel) or buried cables close by. Try moving the boundary wire. The product finds it hard to distinguish Place the product in the charging sta- the signal from another product installation and generate a new loop signal. tion close by. Refer to To create a New loop signal on page 26. Empty battery The product cannot find the charging station. Check that the charging station and the guide wire are installed in accordance with the instructions. Refer to Installation of the product on page 20. The guide wire is broken or not connec- Find out where the break is and rectify ted. it. The battery is spent. Replace the battery. Refer to Battery on page 38. The charging station's antenna is defective. Check if the indicator lamp in the charging station flashes red. Refer to LED indicator lamp on the charging station on page 47. No drive The product has got caught in something. Free the product and rectify the reason for the lack of drive. If it is due to wet grass, wait until the lawn has dried before using the product. The work area includes a steep slope. Maximum guaranteed slope is 45%. Steeper slopes should be isolated. Refer to To put the boundary wire in a slope on page 18. The guide wire is not laid at an angle on a slope. If the guide wire is laid on a slope, it must be laid at an angle across the slope. Wheel motor over- The product has got caught in some- loaded thing. Free the product and rectify the reason for the lack of drive. If it is due to wet grass, wait until the lawn has dried before using the product. 42 - Troubleshooting 1230 - 001 -

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
Menu structure overview 1	7
Menu structure overview 2	8
Menu structure overview 3	9
Display	10
Keypad	10
Safety	11
Safety definitions	11
General safety instructions	11
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	12
Safety instructions for operation	13
Use	13
Battery safety	14
How to lift and move the product	14
Maintenance	15
In the event of a thunderstorm	15
Installation	16
Introduction - Installation	16
Before the installation of the wires	16
Before the installation of the product	16
To examine where to put the charging station	16
To examine where to put the power supply	17
To examine where to put the boundary wire	17
To put the boundary wire in a slope	18
Passages	18
To make an island	18
To make a secondary area	19
To examine where to put the guide wire	19
Work area examples	20
Installation of the product	20
To install the charging station	20
To install the boundary wire	21
To install the guide wire	21
To put the wire into position with stakes	22
To bury the boundary wire or the guide wire	22
To extend the boundary wire or the guide wire	22
After the installation of the product	22
To do a visual check of the charging station	22
To do the basic settings	23
Automower® Connect app	23
To install the Automower® Connect app	23
Automower® Connect menu	23
Dashboard	23
Map	24
Settings in Automower® Connect	24
To do the product settings	24
To get access to the menu	24
To do the timer settings	24
To calculate the timer setting	24
To set the timer	24
To copy the timer setting	24
To reset the timer setting	25
Cutting height	25
To set the cutting height	25
Security level	25
To set the security level	25
To change the PIN-code	26
To create a New loop signal	26
To set duration of alarm and time lock	26
Messages	26
To read the messages	26
Weather timer	26
To set the Weather timer	27
Installation	27
Lawn coverage	27
To disable and enable the GPS function	27
To set the Lawn coverage function	27
To do a test of the Lawn coverage function	28
To measure the distance from the charging station	28
To disable or enable the Lawn coverage function	28
Finding the charging station	28
To set the delay time for the guide wire and the boundary wire	29
To disable the guide wire and boundary wire	29
To test if the product can find the charging station	29
To reset the settings for the guide wire and the boundary wire	29
To change the signal range of the charging station	29
Advanced	29
Corridor width	29
To set the corridor width	29
Exit angles	30
To set the exit angles	30
To set the reversing distance	30
To set the Drive Past Wire function	30
Settings	30
Profiles	30
To save settings to a profile	30
To use a profile	31
ECO mode	31
To set the ECO mode	31
Spiral Cutting	31
To set the level of Spiral Cutting	31
Slope Control	31
To enable or disable the Slope control	31
General	31
To set the time & date	31
To set the language	32
To set the Country & Timezone	32
To reset all user settings	32
The About menu	32
Accessories	32
Information	32
Automower® Connect	32
To pair Automower® Connect and the product	32
To set the Geofence level of sensitivity	32
To use the SMS function	32
Network	33
SIM PIN	33
APN settings	33
To reset the Automower® Connect settings	33
Headlights	33
To set the schedule for the headlights	33
To set the Flashes when fault function	33
Ultrasonic (Automower® 450XH)	33
To set the Ultrasonic function	33
Mower house	33
To avoid collisions with the mower house	33
Operation	34
Main switch	34
To start the product	34
Operating mode - Start	34
Main area	34
Override timer	34
Secondary area	34
Spot cutting	35
Operating mode - Park	35
Park until further notice	35
Start again in 3 hours	35
Start with next timer	35
To stop the product	35
To switch off the product	35
To charge the battery	35
Maintenance	37
Introduction - maintenance	37
Clean the product	37
Chassis and blade disc	37
Chassis	37
Wheels	37
Cover	37
Charging station	37
Replace the blades	38
To replace the blades	38
Battery	38
Winter service	39
Troubleshooting	40
Introduction - troubleshooting	40
Fault messages	40
Information messages	45
LED indicator lamp on the charging station	47
LED indicator lamp on the product	48
Symptoms	49
Finding breaks in the loop wire	50
Transportation, storage and disposal	53
Transportation	53
Storage	53
Disposal	53
To remove the battery	53
Technical data	54
Technical data	54
Warranty	57
Warranty terms	57
Applicable to US/CA market	58
Supplier's Declaration of Conformity	58

Match case Limit results 1 per page

Message

Cause

Action

Outside work area

The boundary wire connections to the

charging station are crossed.

Check that the boundary wire is con-

nected correctly.

The boundary wire is too close to the

edge of the work area.

Check that the boundary wire has been

laid according to the instructions. Refer

To install the boundary wire on page

The work area slopes too much by the

boundary loop.

The boundary wire is laid in the wrong

direction around an island.

Disturbances from metal objects (fen-

ces, reinforcement steel) or buried ca-

bles close by.

Try moving the boundary wire.

The product finds it hard to distinguish

the signal from another product installa-

tion close by.

Place the product in the charging sta-

tion and generate a new loop signal.

Refer to

To create a New loop signal

on page 26

Empty battery

The product cannot find the charging

station.

Check that the charging station and the

guide wire are installed in accordance

with the instructions. Refer to

Installa-

tion of the product on page 20

The guide wire is broken or not connec-

ted.

Find out where the break is and rectify

it.

The battery is spent.

Replace the battery. Refer to

Battery

on page 38

The charging station’s antenna is de-

fective.

Check if the indicator lamp in the

charging station flashes red. Refer to

LED indicator lamp on the charging sta-

tion on page 47

No drive

The product has got caught in some-

thing.

Free the product and rectify the reason

for the lack of drive. If it is due to wet

grass, wait until the lawn has dried be-

fore using the product.

The work area includes a steep slope.

Maximum guaranteed slope is 45%.

Steeper slopes should be isolated. Re-

fer to

To put the boundary wire in a

slope on page 18

The guide wire is not laid at an angle

on a slope.

If the guide wire is laid on a slope, it

must be laid at an angle across the

slope.

Wheel motor over-

loaded