IBM 88632SU User Manual - Page 38

Attention

Get IBM 88632SU PDF manuals and user guides View all IBM 88632SU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Attention: Static electricity that is released to internal server components when the server is powered-on might cause the server to halt, which could result in the loss of data. To avoid this potential problem, always use an electrostatic-discharge wrist strap or other grounding system when working inside the server with the power on. To install a hot-plug PCI adapter, complete the following steps. Note: For hot-pluggable adapters, make sure that the PCI hot-plug device driver is installed. 1. Read the safety information beginning on page v and "Installation guidelines" on page 20. 2. If the adapter is not hot-pluggable, turn off the server and peripheral devices, and disconnect the power cords and all external cables. 3. Remove the server cover (see "Removing the cover and bezel" on page 22) and determine which PCI expansion slot you will use for the adapter. PCI retaining bar PCI divider Attention Tab LED (yellow) Power LED (green) Adapter retention latch DCAC 4. See the documentation that comes with the adapter for instructions for setting jumpers or switches and for cabling. Note: Route adapter cables before you install the adapter. 5. Install the adapter: a. Open the blue PCI retaining bar by lifting the front edge. b. Push the orange adapter retention latch toward the rear of the server and open the tab. The power LED for the slot turns off. c. Remove the expansion-slot cover. 26 IBM System x3850 Type 8864: User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Attention:
Static
electricity
that
is
released
to
internal
server
components
when
the
server
is
powered-on
might
cause
the
server
to
halt,
which
could
result
in
the
loss
of
data.
To
avoid
this
potential
problem,
always
use
an
electrostatic-discharge
wrist
strap
or
other
grounding
system
when
working
inside
the
server
with
the
power
on.
To
install
a
hot-plug
PCI
adapter,
complete
the
following
steps.
Note:
For
hot-pluggable
adapters,
make
sure
that
the
PCI
hot-plug
device
driver
is
installed.
1.
Read
the
safety
information
beginning
on
page
v
and
“Installation
guidelines”
on
page
20.
2.
If
the
adapter
is
not
hot-pluggable,
turn
off
the
server
and
peripheral
devices,
and
disconnect
the
power
cords
and
all
external
cables.
3.
Remove
the
server
cover
(see
“Removing
the
cover
and
bezel”
on
page
22)
and
determine
which
PCI
expansion
slot
you
will
use
for
the
adapter.
AC
DC
Tab
Adapter
retention
latch
Attention
LED
(yellow)
Power
LED
(green)
PCI retaining
bar
PCI
divider
4.
See
the
documentation
that
comes
with
the
adapter
for
instructions
for
setting
jumpers
or
switches
and
for
cabling.
Note:
Route
adapter
cables
before
you
install
the
adapter.
5.
Install
the
adapter:
a.
Open
the
blue
PCI
retaining
bar
by
lifting
the
front
edge.
b.
Push
the
orange
adapter
retention
latch
toward
the
rear
of
the
server
and
open
the
tab.
The
power
LED
for
the
slot
turns
off.
c.
Remove
the
expansion-slot
cover.
26
IBM
System
x3850
Type
8864:
User’s
Guide