IBM 88632SU User Manual - Page 57

approximately

Get IBM 88632SU PDF manuals and user guides View all IBM 88632SU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Air baffle Heat sink FRONT Microprocessor FRONT FRONT FRONT Microprocessor baffle VRM 4 Note: The new microprocessor comes in a kit with a VRM and a heat sink. The VRM is used only with a microprocessor that is installed in socket 3 or 4. 4. Lift the air baffle out of the microprocessor tray. 5. Remove the microprocessor baffle from a microprocessor socket and store it for future use. 6. Remove the protective cover, tape, or label from the surface of the microprocessor socket, if any is present. 7. Lift the microprocessor-release lever to the fully open position (approximately 135° angle). Lever closed Lever fully open Note: Two of the microprocessor sockets are mounted on the microprocessor board with the microprocessor-release lever on the opposite side. These sockets are rotated 180° on the microprocessor board. Be sure to verify the orientation of the socket before installing the microprocessor. Chapter 2. Installing options 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Heat sink
Microprocessor
Microprocessor
baffle
VRM 4
FRONT
Air baffle
FRONT
FRONT
FRONT
Note:
The
new
microprocessor
comes
in
a
kit
with
a
VRM
and
a
heat
sink.
The
VRM
is
used
only
with
a
microprocessor
that
is
installed
in
socket
3
or
4.
4.
Lift
the
air
baffle
out
of
the
microprocessor
tray.
5.
Remove
the
microprocessor
baffle
from
a
microprocessor
socket
and
store
it
for
future
use.
6.
Remove
the
protective
cover,
tape,
or
label
from
the
surface
of
the
microprocessor
socket,
if
any
is
present.
7.
Lift
the
microprocessor-release
lever
to
the
fully
open
position
(approximately
135°
angle).
Lever closed
Lever fully
open
Note:
Two
of
the
microprocessor
sockets
are
mounted
on
the
microprocessor
board
with
the
microprocessor-release
lever
on
the
opposite
side.
These
sockets
are
rotated
180°
on
the
microprocessor
board.
Be
sure
to
verify
the
orientation
of
the
socket
before
installing
the
microprocessor.
Chapter
2.
Installing
options
45