IBM LS41 User Guide - Page 51

Closing, blade, server, cover

Get IBM LS41 - BladeCenter - 7972 PDF manuals and user guides
UPC - 883436021159
View all IBM LS41 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Closing the blade server cover Attention: You cannot insert the blade server into the BladeCenter unit until the cover is installed and closed or an expansion unit is installed. Do not attempt to override this protection. The following illustration shows how to close the blade server cover. Blade-cover release Blade-cover release To close the blade server cover, complete the following steps: 1. Read the safety information beginning on page v and "Installation guidelines" on page 17. 2. If you removed the bezel assembly, replace it now (see "Installing the bezel assembly" on page 37 for instructions). 3. If you removed an expansion unit from a double-width type blade server, replace it now (see "Installing an expansion unit" on page 38 for instructions). 4. Lower the cover so that the slots at the rear slide down onto the pins at the rear of the blade server, as shown in the illustration. Before closing the cover, make sure that all components are installed and seated correctly and that you have not left loose tools or parts inside the blade server. 5. Pivot the cover to the closed position, as shown in the illustration, until it clicks into place. Chapter 3. Installing options 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Closing
the
blade
server
cover
Attention:
You
cannot
insert
the
blade
server
into
the
BladeCenter
unit
until
the
cover
is
installed
and
closed
or
an
expansion
unit
is
installed.
Do
not
attempt
to
override
this
protection.
The
following
illustration
shows
how
to
close
the
blade
server
cover.
Blade-cover
release
Blade-cover
release
To
close
the
blade
server
cover,
complete
the
following
steps:
1.
Read
the
safety
information
beginning
on
page
v
and
“Installation
guidelines”
on
page
17.
2.
If
you
removed
the
bezel
assembly,
replace
it
now
(see
“Installing
the
bezel
assembly”
on
page
37
for
instructions).
3.
If
you
removed
an
expansion
unit
from
a
double-width
type
blade
server,
replace
it
now
(see
“Installing
an
expansion
unit”
on
page
38
for
instructions).
4.
Lower
the
cover
so
that
the
slots
at
the
rear
slide
down
onto
the
pins
at
the
rear
of
the
blade
server,
as
shown
in
the
illustration.
Before
closing
the
cover,
make
sure
that
all
components
are
installed
and
seated
correctly
and
that
you
have
not
left
loose
tools
or
parts
inside
the
blade
server.
5.
Pivot
the
cover
to
the
closed
position,
as
shown
in
the
illustration,
until
it
clicks
into
place.
Chapter
3.
Installing
options
39