Icom IC-F8101 Instruction Manual - Page 82

RWARNING! DMB-126 Optional mounting bracket, When using the M5 × 16 mm tapping screws

Get Icom IC-F8101 PDF manuals and user guides View all Icom IC-F8101 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

6 CONNECTION AND INSTALLATION D MB-126 (Optional mounting bracket) An optional mounting bracket MB-126 is used to mount the transceiver or transceiver's Main unit onto a flat surface. q A ttach the mounting plates and tighten the 2 supplied M5 × 8 mm screws on each side. e A ttach the Main unit to the mounting bracket, as shown below. w P lace the mounting bracket on the board, and then tighten the 4 supplied screws. M5 × 12 mm M5 × 16 mm Not supplied by Icom Attention to mount on the board: If the supplied rubber feet are attached to the Main unit (p. 67), remove them before attaching it to the mounting bracket. Otherwise the feet get stuck, and you cannot slide the Main unit into the bracket. r T he completed mounting should look like this. • Surface mounting RWARNING! Mount the mounting bracket to a surface that can support more than 10 kg (22 lb). The unit must be mounted on only a flat hard surface. When using the M5 × 16 mm tapping screws: Mount the mounting bracket to a board that is more than 20 mm (0.8 inches) thick. When using the M5 × 12 mm screws: Mount the mounting bracket to a board to which you can firmly tighten the screws with the washers and nuts. • Overhead mounting 76

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
76
6
CONNECTION AND INSTALLATION
q
Attach the mounting plates and tighten the 2 sup-
plied M5
×
8 mm screws on each side.
w
Place the mounting bracket on the board, and then
tighten the 4 supplied screws.
M5 × 16 mm
M5 × 12 mm
R
WARNING!
Mount the mounting bracket to
a surface that can support more than 10 kg
(22 lb). The unit must be mounted on only a flat
hard surface.
When using the M5 × 16 mm tapping screws:
Mount the mounting bracket to a board that is
more than 20 mm (0.8 inches) thick.
When using the M5 × 12 mm screws:
Mount the mounting bracket to a board to which
you can firmly tighten the screws with the wash-
ers and nuts.
e
Attach the Main unit to the mounting bracket, as
shown below.
Not supplied by Icom
Attention to mount on the board:
If the supplied rubber feet are attached to the
Main unit (p. 67), remove them before attaching
it to the mounting bracket. Otherwise the feet
get stuck, and you cannot slide the Main unit
into the bracket.
r
The completed mounting should look like this.
• Surface mounting
• Overhead mounting
D
MB-126 (Optional mounting bracket)
An optional mounting bracket MB-126 is used to
mount the transceiver or transceiver’s Main unit onto
a flat surface.