Icom ID-31A Instruction Manual - Page 61

PROBLEM, POSSIBLE CAUSE, SOLUTION, D-STAR Server. Or it's wrong.

Get Icom ID-31A PDF manuals and user guides View all Icom ID-31A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

TROUBLESHOOTING 8 • While operating D-STAR 1 PROBLEM POSSIBLE CAUSE SOLUTION REF. 2 After your call, the repeater • The repeater setting is wrong. does not transmit a reply. • Set the correct repeater. Advanced • Correct the repeater frequency, frequency offset, or Instruction 3 duplex setting. • T he transceiver is out of the repeater range, or • Try to access another repeater. Section 3 4 your transmission does not reach the repeater. 5 After your call, the repeater • T he call was successfully sent, but no station's • Wait for a while, and try it again. replies 'UR?' and its call signal was immediately received. 6 sign. 7 After your call, the repeater • MY call sign has not been set. • Set the MY call sign. replies 'RX' or 'RPT?' and • Y our call sign has not been registered to the • Register your call sign to the D-STAR Server. Or con- 8 the call sign of its gateway D-STAR Server. Or it's wrong. firm the registration of your call sign. 9 repeater. • Y our calling station call sign has not been regis- • A sk the server's administrator about your calling sta- tered to the D-STAR Server. Or it's wrong. tion's call sign. 10 After your call, the repeater • T he D-STAR cannot connect to the called re- • W ait for a while, and try it again. replies 'RPT?' and call sign peater, or it's busy. 11 of the called repeater. 12 After your call, the repeater • T he call sign of the called repeater is wrong. • Correctly set the called repeater call sign. replies 'RPT?' and its call 13 sign. 14 Even holding down , the • The repeater list has been cleared. • Reprogram the repeater list using the CS-31 clon- DR mode will not appear. ing software. 15 • Reprogram the repeater list with the transceiver. 16 Even holding down , the • The call sign has not been correctly received. • T ry it again, after the transceiver has again received received call sign will not its call sign. 17 set to the operating call sign 18 The repeater does not ac- • Your call sign has not been registered to the D- • A sk your desired repeater's administrator about call 19 cept your gateway call. STAR system sign registration. 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
52
8
TROUBLESHOOTING
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
PROBLEM
POSSIBLE CAUSE
SOLUTION
REF.
After your call, the repeater
does not transmit a reply.
• The repeater setting is wrong.
• The transceiver is out of the repeater range, or
your transmission does not reach the repeater.
• Set the correct repeater.
• Correct the repeater frequency, frequency offset, or
duplex setting.
• Try to access another repeater.
Advanced
Instruction
Section 3
After your call, the repeater
replies ‘UR?’ and its call
sign.
• The call was successfully sent, but no station’s
signal was immediately received.
• Wait for a while, and try it again.
After your call, the repeater
replies ‘RX’ or ‘RPT?’ and
the call sign of its gateway
repeater.
• MY call sign has not been set.
•Your call sign has not been registered to the
D-STAR Server. Or it’s wrong.
•Your calling station call sign has not been regis
-
tered to the D-STAR Server. Or it’s wrong.
• Set the MY call sign.
• Register your call sign to the D-STAR Server.Or con
-
firm the registration of your call sign.
• Ask the server’s administrator about your calling sta
-
tion’s call sign.
After your call, the repeater
replies ‘RPT?’ and call sign
of the called repeater.
• The D-STAR cannot connect to the called re
-
peater, or it’s busy.
•
Wait for a while, and try it again.
After your call, the repeater
replies ‘RPT?’ and its call
sign.
• The call sign of the called repeater is wrong.
• Correctly set the called repeater call sign.
Even holding down
,
the
DR mode will not appear.
• The repeater list has been cleared.
• Reprogram the repeater list using the CS-31 clon
-
ing software.
• Reprogram the repeater list with the transceiver.
Even holding down
,
the
received call sign will not
set to the operating call
sign
• The call sign has not been correctly received.
• Try it again, after the transceiver has again received
its call sign.
The repeater does not ac-
cept your gateway call.
•
Your call sign has not been registered to the D-
STAR system
•
Ask your desired repeater’s administrator about call
sign registration.
• While operating D-STAR