Insignia NS-FTV27 User Manual (English) - Page 12

NS-FTV27 27-inch Flat Stereo Color TV Viewing the previous channel The QUICK VIEW button allows you to go back to the last channel viewed. Press QUICK VIEW again to return to the last channel you were watching. Muting the volume Press MUTE to turn off the sound. The television's sound is silenced and MUTE appears on the screen. The sound can be switched back on by pressing this button again or by pressing one of the VOL + or - buttons. Using sleep To set the television to turn off after a preset amount of time, press SLEEP on the remote control. The clock counts up ten (10) minutes for each press of the SLEEP button (0h00m, 0h10m, ...1h50m, 2h00m). After the sleep time is programmed, the display appears briefly every ten minutes to remind you that the sleep timer is operating. To confirm the sleep timer setting, press SLEEP and the remaining time is displayed for a few seconds. To cancel the sleep timer, press SLEEP repeatedly until the display turns to 0h00m. Setting the V-Chip An age limitation can be set to restrict children from viewing or hearing violent scenes or pictures that you may choose to exclude. The restriction applies to TV rating and movie rating if this data is transmitted. You may set this restriction separately. To use the V-Chip function, you must set a password. Notes • The V-Chip function is activated only on programs and input sources that have the rating signal. • It may take several minutes to complete the initial V-Chip setup. • The V-CHIP SET (DTV) will only be selectable when the TV receives a digital broadcast using the new rating system. Currently, some stations are still not providing this signal. If the signal is not provided, V-CHIP SET (DTV) function will not be available. • If you forget the password, contact Customer Service at 1-877-467-4289 for assistance. Your original remote control is required. • To avoid forgetting the password, write it down and keep it in a safe place. Setting a password To set a password: 1 Press MENU. The menu screen appears. 2 Press or to select the LOCKS menu. 3 Press or to display the password entering mode. 4 Select and enter a password (4 digits) using the number buttons (0-9), then press ENTER. 5 Enter the same password again to confirm, then press ENTER. The password is now set and the V-Chip menu appears on the screen. Setting the V-Chip To set the V-Chip: 1 Press MENU. The menu screen appears. 2 Press or to select the LOCKS menu. 3 Press or to display the password entering mode. Use number buttons (0-9) to enter your password, then press ENTER. The LOCKS menu appears. 4 Press or to select V-CHIP SET, then press . The V-CHIP SET menu appears. 5 Press or to select TV RATING, then press or to display the desired rating. OFF-TV RATING is not set TV-Y-All children TV-Y7-7 years old and above TV-G-General audience TV-PG-Parental guidance TV-14-14 years old and above TV-MA-17 years old and above When you select TV-Y7, TV-PG, TV-14, or TV-MA, press -/DISPLAY to further define the rating. Press or to select the desired rating you want. Press or to select the setting ON or OFF. 6 Press or to select MOVIE RATING, then press . The RATING menu appears. 7 Press or to select the rating, then press or to select ON or OFF for each rating. G-All ages PG-Parental guidance PG-13-Parental guidance less than 13 years old R-Under 17 years old parental guidance suggested NC-17-17 years old and above X-Adult only 8 Press MENU twice to return to the LOCKS menu, then press or to select V-CHIP. 9 Press or to select ON. Your settings are now set into memory. 10 Press EXIT to return to the normal screen. Watching a protected show To watch a program that is blocked by the V-Chip: 1 Press MUTE. 2 Enter the password, then press ENTER. After you enter the password correctly, the protection is temporarily overridden. If the television is turned off, or if the channel is changed, the V-Chip restriction is reactivated. Changing the password To change the password: 1 Press MENU. The menu screen appears. 2 Press or to select the LOCKS menu. 3 Press or to display the password entering mode. Use the number buttons (0-9) to enter your password, then press ENTER. The LOCKS menu appears. 4 Press or to select NEW PASSWORD, then press or . 5 Enter a new password using the number buttons (0-9), then press ENTER. www.insignia-products.com 11