Home » Intel Manuals » Motherboards » Intel D915GUX » Manual Viewer

Intel D915GUX Product Specification - Page 65

Front Panel USB Connectors, INTEGRATOR'S NOTES

Get Intel D915GUX PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Technical Reference 2.8.2.4.1 Hard Drive Activity LED Connector [Yellow] Pins 1 and 3 [Yellow] can be connected to an LED to provide a visual indicator that data is being read from or written to a hard drive. Proper LED function requires one of the following: • A Serial ATA hard drive connected to an onboard Serial ATA connector • An IDE hard drive connected to an onboard IDE connector 2.8.2.4.2 Reset Switch Connector [Purple] Pins 5 and 7 [Purple] can be connected to a momentary single pole, single throw (SPST) type switch that is normally open. When the switch is closed, the board resets and runs the POST. 2.8.2.4.3 Power/Sleep LED Connector [Green] Pins 2 and 4 [Green] can be connected to a one- or two-color LED. Table 32 shows the possible states for a one-color LED. Table 33 shows the possible states for a two-color LED. Table 32. States for a One-Color Power LED LED State Off Steady Green Description Power off/sleeping Running Table 33. States for a Two-Color Power LED LED State Off Description Power off Steady Green Running Steady Yellow Sleeping NOTE The colors listed in Table 32 and Table 33 are suggested colors only. Actual LED colors are product- or customer-specific. 2.8.2.4.4 Power Switch Connector [Red] Pins 6 and 8 [Red] can be connected to a front panel momentary-contact power switch. The switch must pull the SW_ON# pin to ground for at least 50 ms to signal the power supply to switch on or off. (The time requirement is due to internal debounce circuitry on the board.) At least two seconds must pass before the power supply will recognize another on/off signal. 2.8.2.5 Front Panel USB Connectors Figure 19 is a connection diagram for the front panel USB connectors. INTEGRATOR'S NOTES • The +5 V DC power on the USB connector is fused. • Pins 1, 3, 5, and 7 comprise one USB port. 65

Section	Page
Intel® Desktop Boards D915GUX/D915GHA Technical Product Specification	1
Revision History	2
Preface	3
Intended Audience	3
What This Document Contains	3
Typographical Conventions	3
Other Common Notation	4
Contents	5
1 Product Description	11
1.1 PCI Bus Terminology Change	11
1.2 Overview	12
1.2.1 Feature Summary	12
1.2.2 Manufacturing Options	13
1.2.3 Board Layout	14
1.2.4 Block Diagram	16
1.3 Online Support	17
1.4 Processor	17
1.5 System Memory	18
1.5.1 Memory Configurations	19
1.5.1.1 Dual Channel (Interleaved) Mode Configurations	20
1.5.1.2 Single Channel (Asymmetric) Mode Configurations	22
1.6 Intel® 915G Chipset	23
1.6.1 Intel 915G Graphics Subsystem	23
1.6.1.1 Intel® GMA900 Graphics Controller	23
1.6.1.2 Dynamic Video Memory Technology (DVMT)	24
1.6.1.3 Advanced Digital Display 2 (ADD2) Card Support	24
1.6.1.4 Configuration Modes	25
1.6.2 USB	25
1.6.3 IDE Support	25
1.6.3.1 Parallel ATE IDE Interface	25
1.6.3.2 Serial ATA Interfaces	26
1.6.3.3 SCSI Hard Drive Activity LED Connector (Optional)	26
1.6.4 Real-Time Clock, CMOS SRAM, and Battery	27
1.7 PCI Express Connectors	27
1.8 I/O Controller	27
1.8.1 Serial Ports	28
1.8.2 Parallel Port	28
1.8.3 Diskette Drive Controller	28
1.8.4 Keyboard and Mouse Interface	28
1.9 Audio Subsystem	29
1.9.1 Audio Subsystem Software	29
1.9.2 Audio Connectors	29
1.9.3 Intel® High Definition Audio Subsystem	30
1.10 LAN Subsystem	31
1.10.1 10/100 Mbits/sec LAN Subsystem	31
1.10.1.1 Intel® 82562EZ Physical Layer Interface Device	31
1.10.1.2 RJ-45 LAN Connector with Integrated LEDs	31
1.10.2 Gigabit LAN Subsystem	32
1.10.2.1 Marvell Yukon 88E8050 PCI Express 1.0a Integrated MAC/PHY Gigabit Ethernet Controller	32
1.10.2.2 RJ-45 LAN Connector with Integrated LEDs	32
1.10.3 Alert Standard Format (ASF) Support	33
1.10.4 Intel® Wireless Connect Technology (Optional)	33
1.10.5 LAN Subsystem Software	34
1.11 Hardware Management Subsystem	34
1.11.1 Hardware Monitoring and Fan Control ASIC	34
1.11.2 Thermal Monitoring	35
1.11.3 Fan Monitoring	35
1.11.4 Chassis Intrusion and Detection	36
1.12 Power Management	36
1.12.1 ACPI	36
1.12.1.1 System States and Power States	37
1.12.1.2 Wake-up Devices and Events	38
1.12.2 Hardware Support	38
1.12.2.1 Power Connector	39
1.12.2.2 Fan Connectors	39
1.12.2.3 LAN Wake Capabilities	39
1.12.2.4 Instantly Available PC Technology	40
1.12.2.5 Resume on Ring	40
1.12.2.6 Wake from USB	40
1.12.2.7 Wake from PS/2 Devices	40
1.12.2.8 PME# Signal Wake-up Support	40
1.12.2.9 WAKE# Signal Wake-up Support	41
1.12.2.10 +5 V Standby Power Indicator LED	41
1.13 Trusted Platform Module (Optional)	42
1.13.1 System Requirements	42
1.13.2 Warning of Potential Data Loss	42
1.13.3 Security Precautions	43
1.13.3.1 Password Procedures	43
1.13.3.2 Emergency Recovery File Back Up Procedures	44
1.13.3.3 Hard Drive Image Backup Procedures	44
1.13.3.4 Clear Text Backup (Optional)	44
1.13.4 Trusted Platform Module Ownership	44
1.13.5 Enabling the Trusted Platform Module	45
1.13.6 Assuming Trusted Platform Module Ownership	45
1.13.7 Recovery Procedures	46
1.13.7.1 Recovering from Hard Disk Failure	46
1.13.7.2 Recovering from Desktop Board or TPM Failure	46
1.13.8 Clearing Trusted Platform Module Ownership	47
1.13.9 Software Support	48
2 Technical Reference	49
2.1 Introduction	49
2.2 Memory Resources	49
2.2.1 Addressable Memory	49
2.2.2 Memory Map	51
2.3 DMA Channels	51
2.4 Fixed I/O Map	52
2.5 PCI Configuration Space Map	53
2.6 Interrupts	54
2.7 PCI Conventional Interrupt Routing Map	55
2.8 Connectors	56
2.8.1 Back Panel Connectors	56
2.8.2 Component-side Connectors	58
2.8.2.1 Power Supply Connectors	62
2.8.2.2 Add-in Card Connectors	63
2.8.2.3 Auxiliary Front Panel Power/Sleep LED Connector	64
2.8.2.4 Front Panel Connector	64
2.8.2.4.1 Hard Drive Activity LED Connector [Yellow]	65
2.8.2.4.2 Reset Switch Connector [Purple]	65
2.8.2.4.3 Power/Sleep LED Connector [Green]	65
2.8.2.4.4 Power Switch Connector [Red]	65
2.8.2.5 Front Panel USB Connectors	65
2.8.2.6 Front Panel IEEE 1394a Connectors (Optional)	66
2.9 Jumper Block	67
2.10 Mechanical Considerations	68
2.10.1 Form Factor	68
2.10.2 I/O Shield	69
2.11 Electrical Considerations	70
2.11.1 DC Loading	70
2.11.2 Add-in Board Considerations	70
2.11.3 Fan Connector Current Capability	70
2.11.4 Power Supply Considerations	71
2.12 Thermal Considerations	72
2.13 Reliability	74
2.14 Environmental	74
2.15 Regulatory Compliance	75
2.15.1 Safety Regulations	75
2.15.2 EMC Regulations	75
2.15.2.1 FCC Compliance Statement (USA)	76
2.15.2.2 Canadian Compliance Statement	76
2.15.3 European Union Declaration of Conformity Statement	76
2.15.4 Product Ecology Statements	77
2.15.4.1 Disposal Considerations	77
2.15.4.2 Recycling Considerations	77
2.15.5 Product Certification Markings (Board Level)	78
3 Overview of BIOS Features	79
3.1 Introduction	79
3.2 BIOS Flash Memory Organization	80
3.3 Resource Configuration	80
3.3.1 PCI Autoconfiguration	80
3.3.2 PCI IDE Support	80
3.4 System Management BIOS (SMBIOS)	81
3.5 Legacy USB Support	81
3.6 BIOS Updates	82
3.6.1 Language Support	82
3.6.2 Custom Splash Screen	82
3.7 Boot Options	83
3.7.1 CD-ROM Boot	83
3.7.2 Network Boot	83
3.7.3 Booting Without Attached Devices	83
3.7.4 Changing the Default Boot Device During POST	83
3.8 Fast Booting Systems with Intel® Rapid BIOS Boot	84
3.8.1 Peripheral Selection and Configuration	84
3.8.2 Intel Rapid BIOS Boot	84
3.9 BIOS Security Features	85
4 Error Messages and Beep Codes	87
4.1 BIOS Error Messages	87
4.2 Port 80h POST Codes	89
4.3 Bus Initialization Checkpoints	93
4.4 Speaker	94