Intel DG41MJ Product Guide - Page 46

Clearing Passwords, Table 12. Jumper Settings for the BIOS Setup Program Modes

Get Intel DG41MJ - Desktop Board Classic Series Motherboard PDF manuals and user guides
UPC - 735858206907
View all Intel DG41MJ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Intel Desktop Board DG41MJ Product Guide Table 12. Jumper Settings for the BIOS Setup Program Modes Jumper Setting Mode Normal (default) (1-2) Description The BIOS uses the current configuration and passwords for booting. Configure (2-3) Recovery (None) After the Power-On Self-Test (POST) runs, the BIOS displays the Maintenance Menu. Use this menu to clear passwords. The BIOS recovers data in the event of a failed BIOS update. Clearing Passwords This procedure assumes that the board is installed in the computer and the configuration jumper block is set to normal mode. 1. Observe the precautions in "Before You Begin" on page 23. 2. Turn off all peripheral devices connected to the computer. Turn off the computer. Disconnect the computer's power cord from the AC power source (wall outlet or power adapter). 3. Remove the computer cover. 4. Find the configuration jumper block (see Figure 22). 5. Place the jumper on pins 2-3 as shown below. 6. Replace the cover, plug in the computer, turn on the computer, and allow it to boot. 7. The computer starts the Setup program. Setup displays the Maintenance menu. 8. Use the arrow keys to select Clear Passwords. Press and Setup displays a pop-up screen requesting that you confirm clearing the password. Select Yes and press . Setup displays the maintenance menu again. 9. Press to save the current values and exit Setup. 10. Turn off the computer. Disconnect the computer's power cord from the AC power source. 11. Remove the computer cover. 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Intel Desktop Board DG41MJ Product Guide
46
Table 12. Jumper Settings for the BIOS Setup Program Modes
Jumper Setting
Mode
Description
Normal (default) (1-2)
The BIOS uses the current configuration and
passwords for booting.
Configure (2-3)
After the Power-On Self-Test (POST) runs, the
BIOS displays the Maintenance Menu.
Use this
menu to clear passwords.
Recovery (None)
The BIOS recovers data in the event of a failed
BIOS update.
Clearing Passwords
This procedure assumes that the board is installed in the computer and the
configuration jumper block is set to normal mode.
1.
Observe the precautions in "Before You Begin" on page 23.
2.
Turn off all peripheral devices connected to the computer.
Turn off the computer.
Disconnect the computer’s power cord from the AC power source (wall outlet or
power adapter).
3.
Remove the computer cover.
4.
Find the configuration jumper block (see Figure 22).
5.
Place the jumper on pins 2-3 as shown below.
6.
Replace the cover, plug in the computer, turn on the computer, and allow it to
boot.
7.
The computer starts the Setup program.
Setup displays the Maintenance menu.
8.
Use the arrow keys to select Clear Passwords.
Press <Enter> and Setup displays a
pop-up screen requesting that you confirm clearing the password.
Select Yes and
press <Enter>.
Setup displays the maintenance menu again.
9.
Press <F10> to save the current values and exit Setup.
10.
Turn off the computer.
Disconnect the computer’s power cord from the AC power
source.
11.
Remove the computer cover.