Intel DP35DP Product Guide - Page 67

Configuring for Intel® Rapid Recover Technology - raid driver

Get Intel DP35DP - Desktop Board Media Series Motherboard PDF manuals and user guides
UPC - 735858192453
View all Intel DP35DP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

5 Configuring for Intel® Rapid Recover Technology Intel Rapid Recover technology utilizes RAID 1 (mirroring) functionality to copy data from a designated master drive to a designated recovery drive. The master and recovery drives must span 100 percent of the available hard drive space of an array, and only one recovery volume can be present on a system. You can select whether you want the master drive data to be copied to the recovery drive continuously or on request. When using the Continuous Update policy, changes made to the data on the master drive while the recovery drive is disconnected or offline are automatically copied to the recovery drive when it is reconnected. When using the Update On Request policy, the master drive data can be restored to a previous state by copying the data on the recovery drive back to the master drive. Enabling Intel Rapid Recover Technology NOTE Intel Rapid Recover Technology does not support RAID 5. Intel Rapid Recover Technology can be Enabled or Disabled in the system BIOS menu. To enable Intel Rapid Recover Technology, complete following steps: 1. Enter the BIOS menu by pressing the key early during system POST. 2. Go to Advanced Drive Configuration. 3. For the setting Intel Rapid Recover Technology, select to enable it. 4. For the setting Configure SATA as, ensure it is set to RAID. CAUTION If Configure SATA as was previously not set to RAID and you already have an operating system installed, you must reinstall it. Follow the instructions in Chapter 5 to install the Intel Matrix Storage RAID driver during the operating system installation. 5. Exit and save settings. Proceed to "Creating a Recovery Volume." 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
67
5 Configuring for Intel
®
Rapid
Recover Technology
Intel Rapid Recover technology utilizes RAID 1 (mirroring) functionality to copy data
from a designated master drive to a designated recovery drive. The master and
recovery drives must span 100 percent of the available hard drive space of an array,
and only one recovery volume can be present on a system.
You can select whether you want the master drive data to be copied to the recovery
drive continuously or on request.
When using the Continuous Update policy, changes
made to the data on the master drive while the recovery drive is disconnected or
offline are automatically copied to the recovery drive when it is reconnected.
When using the Update On Request policy, the master drive data can be restored to a
previous state by copying the data on the recovery drive back to the master drive.
Enabling Intel Rapid Recover Technology
NOTE
Intel Rapid Recover Technology does not support RAID 5.
Intel Rapid Recover Technology can be Enabled or Disabled in the system BIOS menu.
To enable Intel Rapid Recover Technology, complete following steps:
1.
Enter the BIOS menu by pressing the <F2> key early during system POST.
2.
Go to
Advanced
Æ
Drive Configuration
.
3.
For the setting
Intel Rapid Recover Technology
, select to enable it.
4.
For the setting
Configure SATA as
, ensure it is set to
RAID
.
CAUTION
If
Configure SATA as
was previously not set to
RAID
and you already have an
operating system installed, you must reinstall it.
Follow the instructions in
Chapter 5 to install the Intel Matrix Storage RAID driver during the operating
system installation.
5.
Exit and save settings.
Proceed to “Creating a Recovery Volume.”