Intel SR1530HAHLX User Guide - Page 70

Removing the Drive Carrier SR1530HAHLX, Installing Drive into Drive Carrier

Get Intel SR1530HAHLX - Server System - 0 MB RAM PDF manuals and user guides View all Intel SR1530HAHLX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

3. Open the latch at the front of the hard drive carrier. See letter "A" in the figure below. A AF001583 Figure 39. Removing the Drive Carrier (SR1530HAHLX) 4. Pull out on the black lever and slide the carrier from the server system. 5. Remove the four screws that attach the plastic retention device or the previously installed hard drive to the drive carrier. Two screws are at each side of the retention device or the hard drive. Store the plastic retention device for future use. See letter "A" in Figure 40. 6. Remove the hard drive from its wrapper and place it on an antistatic surface. 7. Set any jumpers and/or switches on the drive according to the drive manufacturer's instructions. 8. With the drive circuit-side down, position the connector end of the drive so that it is facing the rear of the drive carrier. 9. Align the holes in the drive to the holes in the drive carrier and attach it to the carrier with the screws that were attached to the plastic retention device. See letter "B" in Figure 40. A B AF001584 Figure 40. Installing Drive into Drive Carrier (SR1530HAHLX) 48 Intel® Server System SR1530AH / SR1530AHLX / SR1530HAHLX

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
48
Intel
®
Server System SR1530AH / SR1530AHLX / SR1530HAHLX
3.
Open the latch at the front of the hard drive carrier. See letter "A" in the figure
below.
Figure 39. Removing the Drive Carrier (SR1530HAHLX)
4.
Pull out on the black lever and slide the carrier from the server system.
5.
Remove the four screws that attach the plastic retention device or the previously
installed hard drive to the drive carrier. Two screws are at each side of the retention
device or the hard drive. Store the plastic retention device for future use. See letter
“A” in
Figure 40
.
6.
Remove the hard drive from its wrapper and place it on an antistatic surface.
7.
Set any jumpers and/or switches on the drive according to the drive manufacturer's
instructions.
8.
With the drive circuit-side down, position the connector end of the drive so that it is
facing the rear of the drive carrier.
9.
Align the holes in the drive to the holes in the drive carrier and attach it to the
carrier with the screws that were attached to the plastic retention device. See letter
“B” in
Figure 40
.
Figure 40. Installing Drive into Drive Carrier (SR1530HAHLX)
A
AF0015
83
A
B
AF0015
8
4