Invacare CLTD Owners Manual - Page 30

Front Riggings, Installing/Removing Swingaway Front Riggings, Installing, Removing

Get Invacare CLTD PDF manuals and user guides View all Invacare CLTD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

SECTION 4-FRONT RIGGINGS SECTION 4-FRONT RIGGINGS ƽ WARNING After making adjustments, always make sure that parts are properly tightened BEFORE using the wheelchair. Installing/Removing Swingaway Front Riggings CAUTION If front riggings are used, then the seat MUST be adjusted to the highest mounting position - otherwise damage may occur. NOTE: For this procedure, refer to FIGURE 4.1. Installing 1. Turn front rigging to the side (open footplate is perpendicular to wheelchair) and position mounting holes in the front rigging hinge plates with hinge pins on the wheelchair frame. 2. Install the front rigging hinge plates onto the hinge pins on the wheelchair frame. 3. Push the front rigging towards the inside of the wheelchair until it locks into place. NOTE: The footplate will be on the inside of the wheelchair when locked in place. 4. Repeat STEPS 1-3 for opposite side of wheelchair. 5. If necessary, adjust the footrest height. Refer to Installing/Removing Swingaway Front Riggings on page 30 Hinge Pins Telescoping Front Rigging Support Removing 1. Pull the front rigging release lever and rotate the footrest outward. 2. Lift up on front rigging and remove from the wheelchair. 3. Repeat STEPS 1-2 for opposite side of wheelchair. Front Rigging Release Lever Front Rigging Hinge Plate FIGURE 4.1 Installing/Removing Swingaway Front Riggings Compass™SPT™ 30 Part No 1122134

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
SECTION 4—FRONT RIGGINGS
Compass™SPT™
30
Part No 1122134
SECTION 4—FRONT RIGGINGS
±
WARNING
After making adjustments, always make sure that parts are properly tightened
BEFORE using the wheelchair.
Installing/Removing Swingaway Front Riggings
CAUTION
If front riggings are used, then the seat MUST be adjusted to the highest mounting
position - otherwise damage may occur.
NOTE: For this procedure, refer to FIGURE 4.1.
Installing
1.
Turn front rigging to the side (open footplate is perpendicular to wheelchair) and
position mounting holes in the front rigging hinge plates with hinge pins on the
wheelchair frame.
2.
Install the front rigging hinge plates onto the hinge pins on the wheelchair frame.
3.
Push the front rigging towards the inside of the wheelchair until it locks into place.
NOTE: The footplate will be on the inside of the wheelchair when locked in place.
4.
Repeat STEPS 1-3 for opposite side of
wheelchair.
5.
If necessary, adjust the footrest height.
Refer to Installing/Removing
Swingaway Front Riggings
on page 30
Removing
1.
Pull the front rigging release lever and
rotate the footrest outward.
2.
Lift up on front rigging and remove
from the wheelchair.
3.
Repeat STEPS 1-2 for opposite side of
wheelchair.
FIGURE 4.1
Installing/Removing Swingaway
Front Riggings
Telescoping Front
Rigging Support
Hinge
Pins
Front
Rigging
Release
Lever
Front
Rigging
Hinge
Plate