JVC DT-V17G15Z Instruction Manual - Page 10

Index of Parts and Functions (cont.) Rear panel Carry handle Use this handle when carrying the monitor. Security slot Attach a security wire to this slot. Note for connections • Before making any connections, turn off all the equipment. • Use a cord whose plugs correctly match the terminals on this monitor and the equipment. • Plugs should be firmly inserted; poor connections could cause noise. • When unplugging a cord, be sure to grasp its plug and pull it out. • DO NOT connect the power cord until all connections are complete. • Refer also to the user manual of each piece of equipment. 1 REMOTE terminal Terminal for controlling the monitor by an external control (☞ "External Control" on page 22). 2 VIDEO terminals (BNC) Input (IN) and output (OUT) terminals for the composite signals. 3 COMPO. (Y, PB/B-Y, PR/R-Y) terminals (BNC) Input (IN) and output (OUT) terminals for the analog component (color difference) signal. 4 AUDIO (IN) terminals (pin jack) Input terminals for the analog audio signals. ● Use this terminal for the analog audio connection of the SDI. When a superimposed signal (EMBEDDED AUDIO signal on an SDI signal) is input, analog audio signals cannot be input. 5 AUDIO MONITOR OUT (OUT 1, OUT 2) terminals (pin jack) Output terminals for the analog audio signal. ● The terminals emit the audio signals through the AUDIO (IN) terminal or EMBEDDED AUDIO signals through the E. AUDIO SDI/HD SDI/SD SDI (IN 1 or IN 2) input terminal. ● The signal is output from this terminal only when the monitor is on or in "P.SAVE" (power save) mode (☞ page 17). ● The EMBEDDED AUDIO signal... - is decoded into an analog signal, then emitted. - is emitted only when "SDI 1" or "SDI 2" is selected, and when EMBEDDED AUDIO signals come in to the E. AUDIO SDI/HD SDI/SD SDI (IN 1 or IN 2) terminal. 6 E. AUDIO SDI/HD SDI/SD SDI (IN 1, IN 2) terminals (BNC) Input terminals for the SDI/HD SDI/SD SDI signals. ● The terminals accept also EMBEDDED AUDIO signals including up to 16 audio channels with a sampling frequency of 48 kHz. ● Use SDI IN 1 and SDI IN 2 terminal when selecting DUAL LINK SDI for the input. ● The terminals also accept 3G SDI signals. 7 E.AUDIO SDI/HD SDI/SD SDI (SWITCHED OUT) terminal (BNC) Output terminal for the SDI/HD SDI/SD SDI signals. ● The SDI signals of the current input (SDI 1 or SDI 2) are reclocked, then emitted. ● When an input other than SDI 1 and SDI 2 is selected, the SDI signal of the input selected last time is emitted from this terminal. ● The signals are emitted from this terminal only when the monitor is on or in "P.SAVE" (power save) (☞ page 17) mode. ● No signals are emitted when DUAL LINK SDI is selected for the input. 8 DVI-D (HDCP) terminals Input terminal for the DVI-D signal compatible with HDCP. ● When the picture is not displayed correctly, change the setting of "DVI INPUT SEL." (☞ page 21) 9 Screw holes for external battery attachment Attach external battery for DC power supply by using 2 screw holes. Choose the appropriate screw holes from 1, 2 or 3 according to the type of external battery. (Depending on the battery type.) Use the Anton Bauer Dionic 90 (mount: QR DXC-M3A) external battery. Caution: Do not use the external battery for DC 24 V power supply. Use only the battery specified above. If a heavy battery is used, it may fall off depending on the way the monitor is used. p DC switch Turns the DC power on or off. ● You need to press button (☞ i on page 9) on the front panel to turn on the monitor after turning on the DC switch. ● The monitor consumes the battery even while the monitor is on standby. To save battery life, turn off the DC switch. q DC IN terminal DC 12 V (maximum DC 17 V) power input connector. When using DC 12 V power (maximum DC 17 V), check the DC IN terminal pin signal, and use the correct polarity (☞ page 30). If the polarity is reversed, this could cause a fire or personal injury. ● While using both the AC and DC power supply, AC power supply is preferentially used. If the AC power supply is cut off (for example,when turning off the POWER switch), the power supply automatically switches to the DC power supply. ● Use a DC power supply with the LPS (Limited Power Sources) function. w AC IN terminal AC power input connector. Connect the provided AC power cord to an AC outlet. ● Attach the provided power cord holder to prevent accidental disconnection of the AC power cord. (☞ page 31) ● Please review "Safety Precautions (a grounding type plug)" on page 4 carefully. Caution: Do not connect the power cord until all other connections are completed. e POWER switch Turns AC power on or off. ● You need to press button (☞ i on page 9) to use the monitor after turning on the POWER switch. 10