JVC TK-C2301WPRU Instruction Manual - Page 19

KE-19

Get JVC TK-C2301WPRU PDF manuals and user guides View all JVC TK-C2301WPRU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Setup Connecting the Alarm Input/Output Cables Menu settings may be required depending on the connected equipment. (Refer to [AUX FUNCTION](A page 54). The default setting has been set to alarm input (IN:ALARM). m Alarm input terminal Connect the infrared sensor, door sensor, metal sensor, manual switch sensor and the like. v To prevent noise from entering the internal circuit, supply non-voltage setting signal to the alarm input signal. v Do not supply voltage. v Using the menu, you can select whether to set to alarm when the contact is short (MAKE), or when the contact is open (BREAK). v Supply such that the alarm signal stays at a minimum of 200 ms or more. Otherwise, the alarm signal may not be recognized. AUX(IN) GND * Please use a shielded cable. m Alarm output terminal Connect to alarm devices such as alarm, indicator, light or buzzer. v The alarm output signal is open collector output and turns ON during an alarm. (Maximum voltage 16 V, current 30 mA) v This terminal has a polarity. Make sure to connect such that a higher voltage is output from the + terminal than from the - terminal. Otherwise, it will result in damages. 100K AUX(OUT) GND .. E-19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Connecting the Alarm Input/Output Cables
Menu settings may be required depending on the connected equipment.
(Refer to [AUX FUNCTION](
A
page 54).
The default setting has been set to alarm input (IN:ALARM).
m
Alarm input terminal
Connect the infrared sensor, door sensor, metal sensor, manual switch
sensor and the like.
v
To prevent noise from entering the internal circuit, supply non-voltage
setting signal to the alarm input signal.
v
Do not supply voltage.
v
Using the menu, you can select whether to set to alarm when the
contact is short (MAKE), or when the contact is open (BREAK).
v
Supply such that the alarm signal stays at a minimum of 200 ms or
more. Otherwise, the alarm signal may not be recognized.
AUX(IN)
*
GND
Please use a shielded
cable.
m
Alarm output terminal
Connect to alarm devices such as alarm, indicator, light or buzzer.
v
The alarm output signal is open collector output and turns ON during
an alarm. (Maximum voltage 16 V, current 30 mA)
v
This terminal has a polarity. Make sure to connect such that a higher
voltage is output from the + terminal than from the - terminal.
Otherwise, it will result in damages.
AUX(OUT)
GND
100
K
Setup
E-19