JVC TK-C2301WPRU Instruction Manual - Page 31

Mount the camera unit to the base, Mount the base to the pipe

Get JVC TK-C2301WPRU PDF manuals and user guides View all JVC TK-C2301WPRU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Installation 4 Mount the base to the pipe Turn and screw the base unit to the pipe in the clockwise direction. Note When screwing the pipe, do not screw beyond 12 mm. Doing so can damage the camera interior. 5 Secure the base unit to the ceiling Use the M4 screw (x2) to secure the base firmly to the ceiling. Note v Make sure there is no gap between the ceiling and the base. v The M4 screws are not provided. Use a suitable type of screws according to the material of the mounting location. 6 Mount the fall prevention wire to a structurally strong location 3 12 mm and below Sealing tape 6 Fall prevention wire 4 8 mm 2 mm . 5 M4 screw 7 Connect the cables (A page 25) Push the connector of the connected coaxial cable back to the pipe. 8 Mount the camera unit to the base ① Push in until the catch (2 locations) snaps on. Note Make sure that the cables and the fall prevention cable are not caught between the camera and the base during mounting. ② Fasten the camera unit fastening screw (2 locations) to secure the camera. 9 The procedures for the following are the same as that for normal camera mounting - Process after connection (A page 26) - Adjusting images (A page 34) - Mounting the dome cover (A page 27) E-31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
4
Mount the base to the pipe
Turn and screw the base unit to the pipe in the clockwise direction.
Note
When screwing the pipe, do not screw beyond 12 mm. Doing
so can damage the camera interior.
5
Secure the base unit to the ceiling
Use the M4 screw (x2) to secure the base firmly to the ceiling.
Note
v
Make sure there is no gap between the ceiling and the base.
v
The M4 screws are not provided. Use a suitable type of
screws according to the material of the mounting location.
6
Mount the fall prevention wire to a structurally strong location
3
4
5
6
2 mm
8 mm
12 mm and below
Fall prevention wire
M4 screw
Sealing tape
7
Connect the cables (
A
page 25)
Push the connector of the connected coaxial cable back to the pipe.
8
Mount the camera unit to the base
①
Push in until the catch (2 locations) snaps on.
Note
Make sure that the cables and the fall prevention cable
are not caught between the camera and the base during
mounting.
②
Fasten the camera unit fastening screw (2 locations) to secure the
camera.
9
The procedures for the following are the same as that for normal
camera mounting
- Process after connection (
A
page 26)
- Adjusting images (
A
page 34)
- Mounting the dome cover (
A
page 27)
Installation
E-31